MAH7500AWW Maytag Washer - Instructions

Removed the old hoses and screwed on the new hoses.

Unplugged, turned water off, removed hoses. Removed screws, unplugged wires, disconnected interior hose and replaced old water inlet valve with new one. Reassembled. Repair was completed by my 17 yr old son in 20 minutes.

The replacement of the drain pump was very easy. I will not go into detail, just follow the video installation provided on this site and you will have no problem.

I decided to replace the drive belt since I was into the back of the washer. The video on this site was spot on, however I did have to apply a lot of effort putting the new one on. My old belt was stretched out considerably and at first thought I had a wrong replacement belt. Number on the belts confirmed it was correct. Just had to walk the belt on the larger pulley and it will fit.

My washer is running like a new one!

First I removed all the screws, which removed the door. Once the door was off, was able to de-install all the parts of the old door and install on the new door. The engineers that design this, made it to be able to replace easily. Inner door part was replaced in less than 30 mins. The most amazing part was I order the part on Monday and the door was fix on Tuesday before 2:00. I was amazed. Thanks

Ordered part from PARTSELECT.COM, super fast shipping, next day actually, via fed ex. Part was exact replacement with no surprises. Swapped out internal parts snapped door lid cover in and was doing a wash in 15 minutes start to finish.

Unscrew the screws holding the soap/bleach/fabric softner in place. Unscrew the door hinges.Unscrew the white plastic clips that are to the right of the door. These hold the front of the washer in place. Once these are removed, you can pull the front of the washer away from the door opening. It leans out from the top and you can remove the entire piece from the clips that hold it in place at the bottom. Then you can unscrew the screws to the top left and top right that hold the top of the washer in place. Once these screws are removed, you can lift up the top of the washer and lean it back revealing the water inlet valve w/thermister. All the electrical connections are easy clip off/clip on. The hose clamp is the typical screw type.

To replace the light bulb, I removed the screw and the cover, unscrewed the old bulb, replaced with the new bulb and replaced the cover, securing it with the small screw. It worked appropriately with normal use for a few days and then I noticed the light was not coming on when I opened the door.

I removed the cover and pulled out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.

First I remove the 2 screws that hold the door on then put it on the table on a towel not to scratch the door and unscrewed the inner door and changed it out easy stuff.

Removed outer door and positioned it on counter next to new part.
Transitioned each part element from from one to the other.
Finally re-install door back in place..........

Repair went just as video on this website indicated. Reinstalling the cable clamp was the hardest part.

Using the video tape (YouTube URL) provided, I went step by step and replaced the bellows with no problem. No water leaking..the toughest part was putting the spring back on, it takes some coordination and muscle.

I followed the steps on the first post which are very good. I had trouble, however, putting the seal over the drum. I finally removed the plastic rim to the drum by removing the clips. I was then able to lay the rim on the floor and put the new seal over it more easily. It is a lot like putting a bicycle tire on a rim. I had no helpers so I used a vice grip pliers on one end of the cable-spring and another pliers on the other. I was then able to pull both ends together enough to get them to hook up. I recommend removing the plastic rim as I mention above. Had I done this first, I would have done the job in less than 30 minutes.

We followed the directions in other people's repair stories here. Removing the spring was a challenge, as was getting it back on! The rest of the repair was simple. Be patient with removing the soap dispenser. Ours had some plastic cords connecting it to the frame which we didn't anticipate, and we broke them because we didn't see them.

We're going to try that new Affresh product in the hopes of avoiding this repair again in the future. We never washed anything harmful in the washer. This seal becomes moldy and deteriorates with time. Using bleach to kill the mold only speeds the process.

after cutting my hand I installed masking tape around the opening on the back of the washer. All went well after that

After watching the repair video, The job became very easy. Thank you parts select, the only thing i didn't like, was the shipping cost. thought it was a little high for such a small and light part..