MAV5000AWW Maytag Washer - Instructions

Removed old agitator, and installed new one. Very easy.

Needed a medium extension and a rachet a screw driver and a 13mm socket. I used a short screw driver and inserted in it the softer container and lifted it strait up to get the softner container out of the way. I used the medium extension to reach in the auger and loosen the small bolt holding the auger on the machine. Pulled it up and out. Reversed the above procedure and it was set to go. Total time about 8 to 10 minutes. Thank for all the help Kudos to all including Susan W.

it took a little longer to fix the lid switch becasue the you have to figure out how to install the switch after you takethe old one out. The old one popped out but the new one needs some twisting and pressure. It also is an ackward position to work in on the back of the washer front the front. I think the instructions could have been much better by warning the installer to pay attention when you take the old one out. But it worked and we fixed the problem for $22 and four days of waiting for the part.

I opened up the control panel on the back by removing the 4 screws and then used the print that was inside to check where the power went from the power cord. I checked the power at diferent places and determined that I did not have power coming from the lid switch with the door up or down. You could here the switch click when you opened and closed the door but aperantly it was not working. After going on your web site and looking at the other posts I realixed that there was a fuse link in the switch that was probably blown. I ordered the switch and it was a simple matter to replace when it arrived. The washer works great once more.

took off front of washer , took off hose clamp removed old hose . replaced with new hose clamped back on put on front cover ran washer check for any leakes. done and done

After replacing the tub to pump hose, I adjusted the feet on the washer. Apparently, the main pulley sits so low on these washers that it ground into the floor and stripped out the thrust bearing. I ordered the new thrust bearing clip and put it in the evening I received it. The instructions it came with were very helpful and it was simple to reassemble. Up until the last piece - the retaining clip. The majority of the repair time was spent replacing that clip. If there is a tool that makes the job easier, I didn't have it. I finally got it on with two flathead screwdrivers prying the shaft out while I wedged one corner of the clip in the groove.

first remove drive belt then then remove dust cover on bottom of shaft take 5/16 nut driver to only 4 of the screws off that hold the brake cover on install 4 5/16 screws 1" long in those 4 spots.reomve rest of screws then slowly reomve back out 1" screws to relve spring pressure from brake pad.install all new parts from partsselect.com then install other part taken off in oreder and make your wife very happy

I did a continuity check on the lid switch assembly since it was a) the easist to get to, and b) my wife's descreiption of how rthe washer stopped made me think it had something to do with the lid switch.
I found that all of the contacts were open regardless of the position of the switch, and I also discovered that there was a fuse inside the swithch. I decided to order a replacement part based on the presence of the fuse.
Upon repacling the fuse (a snap in affair), the washer was working again... my wife was impressed and I was happy!

I didn’t have special tool for brake but punch and hammer worked. Seal was easy to replace. Several videos online to show you how. It wasn’t worth it to tear apart the transmission and buy more parts/seals (if they were even available). But I didn’t know how much oil was in it. I drilled a hole in the side to somewhat check level and added 80-90 gear oil. It was almost empty and added almost a quart. Used a self taping screw/bolt with gasket sealer to plug the hole. I got 34 yrs out of this washer. If it fails, oh well. Just hate to buy a new one that only last 10yrs if im lucky.

I removed three small bolts on the back of top panel unpluged electric plug on lid switch popped out old switch popped in new plugged in switch put top back on with the three small bolts. The wife was back in business. Easy as 1 2 3

The replacement was very easy, just one bolt and RR was a snap. However, the first part that came was defective and I called the 800 number, spoke to the rep and the part came the next day. Excellent customer service, and would do business again

Simple remove and replace. Plastic cam and hinges simply snap out, replacement parts snap right back in. Needle nose pliers were helpful to remove broken lid cam. With hinges and lid removed, took advantage of great opportunity to clean lid and and top of washer.

Took off the top rear off the washer, Removed the top control section,disconnected the wire harness, snaped out the old switch and installed the new one, connected the wire harness, put everything back together, and it was working again!

I opened up the top of the washer which exposed the tub, I took the top ring off the tub and under in side of the ring is the seal. Took the old one out and put the new one in. The old seal was completely wore out.
It was real easy.
Finding the part is usually the hardest part, but thanks to Parts Select finding the part was the easiest part of the repair.

I first took the fabric softener dispenser off and used
a ratchet wrench to take the nut off. I then removed
the agitator, put the new one on and reversed the process. It was extremely easy!