MAV7258AWW Maytag Washer - Instructions

Brought unit out to garage so I would have room to work on it. Popped the top off, removed two screws to remove the front panel, removed back panel also, since there was no way I was going to the trouble of dis-assembly to get to the snubber without changing those 6 springs also - and you HAVE to remove the back cover to access all 6 springs.Removed belt and level and drain hoses- tub came right out. Loosened those 6 screws without removing them and pulled old snubber out- very straight-forward. Spent 10 minutes just comparing the old and new snubbers- I saw that there's a "ridge" around the inside of the new part that is gone on the old snubber. Sprinkled some corn starch at base of unit where the new snubber will fit (Great Idea someone had!) After everything was re-assmbled, I noticed the tub was now nice and tight when I grabbed it to move it. Before, it took no effort AT ALL to move it all around. Did a test load with some laundry the wife had stacked on the drier. Imagine my disappointment when I heard loud knocking inside when it started to agitate, but not while it spun!
Got all my tools back out and took the wet laundry out to take it all apart again- found the wife's heavy glass vase had been hidden in one of the towels. Re-tested- everything works GREAT!So far I've changed the drum seal (hardest) and the waterpump (easiest)- thi springs and snubber was alsmost as easy as the pump.
Above average shipping from Parts Select also- very helpful and efficient people on the phones.

Pop the cap off the agitator/auger no tools needed. Once removed select a socket and a socket exstension. remove the screw amd pull off the part. Make sure to save the washer that may be still attached to the inside of the agitator. install the new agitator using the existing screw and washer. Takes about 15 minutes.

Removed 5 screws on back of the control tower.

removed the temperature control board and replaced with new board.

First I raised the top and took out the two screws that held the front on. Then I removed the back panel which were held by 4 screws. Then I turned the machine on it side and removed the belt. I then pulled the hose off from the tub to the water pump and the small hose on the back of the tub. I then removed the 6 springs that held the tube to the base and then I picked the tub up and turned it over on the floor. Then I backed off on the screws that held the snubber in place. I pulled the old snubber out, retighten the screws that held the snubber tight. Then I reversed my steps.

I unplugged the machine, tipped it back slightly and rested in on a gallon paint can. I inspected the under side and manually advanced the fan belt to hear if I could hear the noise at the water pump. The pump pulley and shaft was worn and there were metal shavins (small) on surface of pulley.

Then I removed the belt from the pulley, rested the machine back to normal position, removed front panel (two sheet metal screws on inside top), removed the water pump hoses (htere is water int he hose & pump assembly so you will get some water on floor.

Then I removed the pump and ordered a new one. The installation was the reverse, machine works like new and the washer tub spins better than ever during the final rinse and spin, since the worn water pump was binding and stressing the machine.

Thanks to Part Select - Your website is awesome and your service instructions and user advice gave me the confidence to do the repair myself. I saved $150 - $250 for the repair.

Replacing the pump with the new pump was very easy for me, because of my degree in Mechanical engineering, so I am use to dealing with pumps, engines, gears,etc. However, my wife watched me do the entire job and she is now able to replace this part in the future. The design of the Maytag is very simple to repair, and for that I am very greatful that we can order the parts and do the repairs ourselves withhout having to call a repairman. This was our first problem after 6 years of smooth operations by this washer.

Removed the front panel to get some light in to the machine. Removed the two hoses connecting the pump to the drain and tub. Removed the three screws holding the old pump in place. Did the reverse to install.
This was a piece of cake.
Thanks for having the parts needed to do this job.
Tom

remmoved the screws on the back that hold the panel on. removed the two hoses attched to the pump. removed three screws and pulled the pump out. spun the pulley and noticed no movement inside. looked closer at the pulley to notice it was broken. ordered new pulley online. received quickly. new part fit exacttly right. put three screws back in. hooked two hoses back up. put belt on pulley. plugged in and worked great.

As described in video; however, the video does not match the model I repaired. Most stuff is the same. Hardest thing to do was installing the new springs on the back of the tub (2 of them).

Removed the inner basket and outer tub to replace the gasket and rubber seal. just had to remove about a dozen screws to get it out.

Tipped the machine up to replace the belt.
The noise didn't go away at first. I decided to spray all the pulleys with some silicone spray, that did the trick.

Shut-off water + power.With the putty knive; slide it under the front of the top to push back on the spring clips.The top will lift easily and it is hinged.The Water inlet unit in the back has a plastic cover.Remove carefully.One screw holds the unit in place. Remove and the the unit will slide out to the left. It's now easy to disconnect the hoses from the unit. The wiring to the coils is color coded,take note for proper reconnecting. Remove stakon connectors from the valve coils. Careful, do not pull on the wire but wiggle it of the coil connection.Pay attention to the routing of the wire harness. Also the kit comes with a clear plastic splash shield. make sure the new goes in the right place.Now the old water inlet valve can be removed from the metal bracket.One srew.Assembly goes in reverse

Followed the excellent utube instructions you provide. Piece of cake when I followed the video. The rear springs became much more difficult because my model does not have rear access panel. They were the only stuggle. Thank you for doing the repair videos

Part Select data showed that over 60% of the time, this issue of the washer shaking was due to broken support springs for the tub and over 30% of the time, it was a worn/broken snubber ring. So, I initially purchased the six springs and snubber ($30 total) from this site and completed both of those repairs. I leveled the washer securely and tested it again. However, the washer still had the issue of shaking during the spin cycle with no improvement. So, I then researched again for this issue and parts recommended were a lower bearing kit or transmission. Since the transmission replacement was $429, that wasn't worth trying. So, for the $52 lower bearing kit, I ordered it from along with a new belt ($22) (even though the existing belt didn't show any signs of significant wear, but I changed it anyway). The new bearing kit was installed and the washer is now operating like new. I used the current videos on the website for replacing the parts that I ordered, and they were perfect step by step instructions. It made the repair very simple for anyone with any sense of do-it yourself ability and with minimum, ordinary tools. So, for approximately $110 for parts and doing the repair myself, the washer is like new again. Thank you!!!!

Analyzed reason for hot water being turned on when only cold water was set. Determined solenoids were functioning correctly using volt/ohm meter and continued working backwards through the electrical circuit. Upon testing resistance level of 4 button switch was able to determine the switch was functioning intermittently. Validated by checking the power and determined voltage was being transferred to more than 1 connector, which was incorrect. Replaced switch with known good switch (validated new switch was good by checking resistivity) prior to installing. Installed switch and ran washer through cold cycle, hot cycle, and warm cycle to validate fix.

Removed water lines and drain, removed back panel, removed drain lines from pump. Unscrewed 3 screws to remove pump. attached drain lines to new pump, screwed in new pump, reattached everything. Reinstalled belt (very easy, not like an altenator). done