MAV7258AWW Maytag Washer - Instructions

Use a blade to pop off the fabric softener dispenser cup. Use socket and extension to unscrew the single hex bolt that attaches the assembly to the shaft. Lift off the assembly and recover the flat washer. Install the new assembly over the shaft and install the original hex bolt and washer. Tighten firmly. Snap the dispenser cup back in place.

Removed entire cabinet from base, removed drive belt, removed suspension springs, removed tub and transmission together.
Removed 6 screws from brake housing to access snubber. Didn't have the special tool to compress the spring for reassembly, but used 3 longer screws to pull the brake housing back down...worked fine. Reinstalled transmission / tub and replaced all 6 springs. Reassembled cabinet. Unit spins great now...like new.

I'm not a washing machine technician but I did nurse a new Kenmore machine for 23 years and was ready for a replacement. Craigslist advertised a Maytag I was interested in and I bought it with the seller's assurance that it worked perfectly. It didn't and I went online to try and figure out what might be wrong. Clearly, the tub was traveling beyond it's design limit and I suspected a spring or two might be involved. Somewhere online, I found the illustrated parts diagram and then went looking for additional information. To my extreem delight, I came across a do it yourself repair video that demonstrated the procedure well enough that I was completely confident I could make the repair with little effort. That video was one of several service related appliance videos offered for free throughhttp://www.do-it-yourself-washing-machine-and-dryer-repair-help.com/index.html/ The final consideration was whether I could buy the replacement suspension springs and snubber ring for less than I paid for the washer. I found PartSelect and within minutes, I had the parts ordered. The parts arrived within 4 or 5 days, as promised, well packaged and in perfect shape. This morning, using the video as a final reference and the new parts, I completed the repair with only a minor hitch. Without the special spring tool used in the video, I struggled a bit with getting the new springs attached. That's where my wife came in handy (after all, she was movitated). Having her tilt the drum toward the spring landing made it much easier for me to stretch it into place using an adjustable locking plier. I actually enjoyed the whole procedure.

Opened the lid and snapped hinge in to place. The part was an exact match and the job went flawlessly.

I popped off the fabric softener on top of the agitator. Used an extended arm on my socket set to remove the only nut holding the agitator on the motor assembly apparatus. The agitator came off with ease. Just reversed the procedure in replacing the new agitator. This was an easy job.

very easy replacement. was probably broken for a year and only took five minutes to replace. Can't believe we waited so long!

Removed the old part with a screwdriver & installed the new part. It took approximately 2 minutes.

As for how I did the repair , I just followed your instruction video . The instruction video provided by Part Select was very very valuable.
The snubber ring was a piece of cake BUT would have been really difficult without the helpful hints in the video like replacing three of the screws in the rings collar with three longer screws so as not to disturb the spring under it.
The suspension springs were a bit more trouble since my washer doesn't have an access panel on the back however THANKS TO YOUR TIP to stretch the spring and put coins between the coils made this much easier . I don't know many guys that are strong enough to lay down and reach through the front and put those springs on the back.
Of coarse the belt was easy.

I also really like you list of probable solutions to the problems with the machine.

My wife is now happy with her washer again therefore I am also happy.

Thanks so much.
I can see me being be a loyal customer for many years to come.

Removed front panel also right side panel to get to the springs. Used vise grips to extend springs and used coins to keep springs open for replacing.

Parts needed: Snubber Ring and 6 Springs (don't put the old springs back)
Unlug the AC cord, open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back It was not necessary to remove the back cover. Remove the little hose going to the basket from the control module. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING: DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK. Seriously! Install the new ring, center and tighten the screws. Put the tub back in. I found it handy to support the tub with a 2x3 to get the springs back in. Connect hoses back up. It really isn’t that bad, a couple of scraped knuckles.

figured out how to open the top of the washer(Two small tabs I pushed in with a putty knife. Looked for the area it was leaking. Slide the hose clamps off with a pliers and pull out hose.

Put clamps on new hose, replace hose and slide clamps to ends to seal the connections

1 I opened the top of the washer found the top plastic rim piece broken due to the fact that it cracked while unbalanced one time. Which made it leak which ate away the rubber seal . The parts were here fast and they were the right ones. Great job and I will tell everyone about you thank you verry much.

disconected water lines unplug power and took drain pipe off, used putty knife to open top of washer and pulled off front removed pannel off back pannel, disconnected water level tube,using vise grips took off springs and pulled tb out used 5/16 socket to loosen screws just enough to pull snubber ring out replaced with new one reversed prosses in putting it back to geather

After just over ten years of use (purchased in early 2001), my Maytag Atlantis started making an awful noise during the spin cycle. The noise was very loud and sounded like metal grating on metal. Looking through posts on partselect.com, I identified the problem as the drain pump and pulley. Looking under the washer I could see that where the pulley connected to the drain pump the metal was starting to fall apart. I ordered the drain pump with pulley and a washer belt. The belt didn't look overly worn, but I figured now was a good time to replace it. The parts arrived within a couple days, faster than I expected. I opened the top of the washer by inserting a putty knife about an inch in on each side to release the top which then easily clam-shells back. I removed the front panel by removing two screws in each corner. Using a few blocks of wood, I propped the washer up in the front so I could remove the drive belt. The motor is spring-loaded and is easily moved to allow for belt removal. Then I removed the two tubes that connect to the drain pump. The drain pump was quickly removed from the washer; only three nuts hold it in place. The new pump/pulley went back into place using the same three nuts. After reconnected the two tubes to the pump, I installed the new drive belt. I put the front panel back on, and seated the top back in place. Anxiously I watched and listened as the washer cycled through a load. To my relief, the problem was fixed. All told, it probably took about 15 minutes to make the repair, and with any luck I’ll get another ten years out of this washer.

Followed directions from video on your site. It was very helpful. The snubber ring fixed the problem.