MAV7650AWW Maytag Washer - Instructions

Removed the front panel, Removed the belt from pump in the back of machine. Removed the pump from the back of machine, Put the pump in reconnected the belt, Replaced all the screws. My husband did the repair work in a matter of 45 minutes. Machine works fine now. The part came when I was told it would. I am very pleased with your service.

The repair it is simple the problem was to figure it out, I did some research on this kind of problem and everything was pointing to the timer so I used a philips screw driver and a nut driver to remove the backside of the control panel,but first don;t forget to unplug the machine, I have to pry off the knob top cover and remove a plastic clip to pull the knob after that you can unplug the electronic board connector and the timer connector,remove a couple of screws amd the timer is out, installation is the reverse of removal.

tip washer up on wooden blocks.remove drive belt.remove "E" clip from tub drive pulley and remove all the parts.Install new parts in kit as per instructions.machine works great!

After pulling the machine away from the wall and turning off the water and unpluging. I simply removed the panel in the back and reached underneath and removed the belt. Took off the hose clamps and removed the three screws holding the pump on. Put the new pump back in place and hooked up the hoses. Then put the belt on for a test run.......all OK put the back on and was done. Whole job about twenty minutes. Saved over two hundred dollars doing this myself. Very simple repair.

i did the repair by the instructions that you had on the web site,and i thank you for all the help you gave me.

For safety I Unplugged the machine
Tipped machine back and removed the belt. Rotated the motor by hand and all is well there. Rotated the water pump by hand and a grinding sound appeared. I Let the machine down . Using a hard object , 1/16th of an inch thick, I slide it between the front edge of the lid and the front panel unlocking the clips ( one on the right side and one on the left side ) holding the lid down. I then tipped the lid up and removed the 2 screws holding the front panel on. Lifted the front panel off of the clips on the bottom end of panel. Using a nut driver I removed the 3 bolts holding the pump to the frame. Then with a pliers I removed the clips holding the 2 hoses. With a pan to catch the water I removed the hoses and drained them into the pan.
I then took my machine model number and went to the internet in search of a new water pump. After checking several sites with no success, I come upon the site for PartSelect.Com. With the excellent search method on the site I was able to quickly find the part I needed. I placed my order (10pm) on a Tuesday night and a short time later I received an email letting me know they had my order. On Wednesday I received an email letting me know they had shipped my order. On Friday the order had arrived.
I removed the new pump from the box and inspected it . Every thing looks great. I placed the pump into its mount on machine and bolted it down. Attached the 2 hoses, put the front panel back on and tipped the top down into place. Pushed machine into place, plugged it in and fired it up. I now have a quiet running machine again. Thank You to PartSelect.com for the quick response to my

Removed the waterlines. Set the ends in a small pan or bucket to catch the water.Do the same with the drain line.
Keep an old towell handy as water will drain out of the drain pump when you remove the drain hose. Removed the back panel. Use a flat bladed screw driver to pop the top off the two clips in front holding the top down. Lift the top and pull the two screws which holds the front in place. Remove the front and set aside. Underneath, use gloves and the screw driver to remove the six springs by placing the screwdriver through the top hook end about an inch and with both hands lift the spring off. Carefull not to let the blade slip off and bust your knuckles on something,hence the gloves. Lean the machine over and walk the belt off the pulley. Disconnect the small tube in the back left corner from the drum and lift the unit out from the top. Set the drum on it's top and loosen the six screws under the big pulley just enough to pull the snubber out. Replace new snubber, tighten screws. Set drum back in place and reattach springs. Lean unit over and replace belt. Reconnect the small tube, back left corner. Replace the front panel and top. Connect the drain line and replace the rear panel. Connect waterlines and check for leaks. I went ahead and replaced all springs. I recommend replacing the belt while your at it. I'm wishing I would have. It runs like new, gets more water out on the spin cycle and the dryer dosn't take as long to dry the clothes.

First I took the front shield off, then I took the motor off.

Read DIY review from William, Middleton, OH on 01-15-08. Tip on how to relieve spring pressure on brake assembly worked like a dream (3ea 10-24X2 bolts/machine screws). Replaced brake and machine works like new and was an inexpensive fix. Once the shell/housing is off the machine, tub can be turned upside down and the base doesn't need to be removed. White powder under machine was a plastic wear ring that tells you when your brake rotor needs to be changed. Brake rotor still had lining but was much thinner than replacement part. Note* Use putty knife to push in clips on front to release the top lid section.

just took the front off and then took the old motor off and switched over about 2 parts from the old to the new and then put the new part on and then placed the front back on and it was ready to go

Very simple, Lid cam part was broken, Just need to remove broken plastic lid cam with screwdriver and then snap in place the new piece. Worked like a charm first time. Easy , inexpensive repair to a reliable washing machine. Bill

Needed a medium extension and a rachet a screw driver and a 13mm socket. I used a short screw driver and inserted in it the softer container and lifted it strait up to get the softner container out of the way. I used the medium extension to reach in the auger and loosen the small bolt holding the auger on the machine. Pulled it up and out. Reversed the above procedure and it was set to go. Total time about 8 to 10 minutes. Thank for all the help Kudos to all including Susan W.

Removed old agitator, and installed new one. Very easy.

took off front of washer , took off hose clamp removed old hose . replaced with new hose clamped back on put on front cover ran washer check for any leakes. done and done

On this particular model #MAV7550AWW Maytag washer, you do not remove a back panel since it is a three sided case. I first disconnected power and hoses from wall. Removed the belt from under the machine (you need to tilt the machine). To access the water pump you need to remove the front panel by first sliding a putty knife between the top of the machine and the panel slide it in about 2 inches from the edge to release the latch, repeat the procedure on the other side. On the inside or the panel about 2 inches there is a nut on either side once you remove both the front panel unlatches easily, from the bottom two latches. The water pump is located on the right front of the bottom plate. it is held in by three nut screws, (have plenty of towels to catch the water that is released once you disconnect the two hoses that are on the pump. The replacement part (made in the USA) is all plastic but fits perfectly. We Replaced the pump and reconnected everything. There is a video here on this site the explains in detail the removal and placement of the drive belt. The job is very simple to do. I am a woman under 5ft and I did this repair with the help of my son (17yr old). The machine is good as new. Second repair I have done on the machine and with a lot of savings!.