MAV7650AWW Maytag Washer - Instructions

Overall, this repair should have been quite easy. The problem was removal of the old seal nut assembly. It was a bear to remove, and ultimately I had to surgically remove it from the washer in pieces. Unfortunately I broke the outer tub (plastic) in the process of getting the nut off. Once I had the silly plastic nut off, and the tub repaired the balance of the repair was absolutely easy.

My summary: This repair is really easy IF the plastic seal nut assembly comes off easily. If it doesn't budget easily, go ahead and chip it apart to get it off, being careful not to damage the threaded part of the agitator shaft. The new one will completely replace the chipped away nut.

I tilted machine onto the front to acces the rear panel. i removed the three screws to expose pump, took of the drive belt located under appliance, removed the three pump screws and removed old defective pump. I installed new pump, put the drive belt back on, reinstalled back panel and screws, hooked the appliance up and started. Been running great ever since. Entire process too about 10 min.

Placed the washer on 2 brick under the front. Removed the belt, used a straight blade screw driver for the lifting of the top off. reoved 2 bolts off the face and removed the screws of the water pump. Water pump was messy with smelly water but a bowel and a towel helps. Placed the pump on, reversed the tear apart...placed the belt on the bottom. Removed the brick under the front. Hooked up the water supply...plugged in and did a load..it worked perfectly....Thanks!!!!

The washing machine would shake very loudly when spinning.
Found red oil under machine. Asked experts, they said "buy new machine, not worth repairing transmission".
replaced small oil seal and drilled small hole and added some transmission oil(auto) then sealed hole. replaced belt just because the other one was oil soaked.
Works great, Like new, cheap fix under $20..

There are two clips that hold the top of the washer down. Releasing these clips allows you to lift the top; it is hinged at the back. Then remove two screws holding the front panel and remove the front panel. The tub to pump hose is easily accessible. It is held in place by a hose clamp at each end. Use pliers to squeeze the clamps and remove the hose. Replace with new hose. I re-used the original clamps.

I felt extremely confident when purchasing the part because I say three diagrams which clearly showed I was ordering the correct part. 0. Drain all of the water out of the machine. 1. Remove the rear panel from the washer. 2. Use the pliers to disconnect the hoses from the pump. 3. Remove the three screwa from the old pump. 4. Support the washer with the block then take the belt off pulley. 5. Remove old pump. 6. put new pump in place then reconnect the pulley, you can remove the block.. 7. Install the three screws for the pump after you tighten it up by placing the pump over ther correct screw holes.. 8. Reconnect the two hoses using the clamps you removed. 9. Secure the rear panel and screw in place. 10. Wash clothes. EASY FIX!!!

Other peice broken or worn out. Poped old one off and new one in......YAHOO!! back to washing clothing again......

Remove front panel and back service panel below water conn. lines. Put a 4" plastic box between the tub and inside of cabinet "directly opposite the spring to be removed to lower the tub to base for less opposing travel to unlatch spring from tub hook. Also took an old slotted screw driver w/ a blade about 1/4 " and grinded 1/8 from middle about an1/8" deep and used it to latch the spring when pushing it up and off the tub. Replaced all 6. Also did motor pivot spring. Tested and the it worked for one cycle, then the tub again just falls to the right as if the spring at 9 o'clock was broke and strains the belt drive but the spin cycle still works o.k. and the washer does not bang and walk away till you stop the machine. Thought the 6 tub springs would take care of both problems. Told that the snubber ring needs to be replaced. Never but another maytag again. JUst did the belt,a week later the water pump went then the springs.....

I opened the front of the machine. The clips had rusted. One broke and the others were very difficult to work with. I pried the panel open with a large screwdriver. I took the back panel off to access the water pump. I removed the back panel on the electricals to access the timer. To replace the timer I pried off the decorative cover. To get the knob off you have to squeeze in on the timer split shaft while pulling out on the know. This was the second hardest part. (The front panel access was the most difficult). After that the timer clip is easy to loosen and it slides a littel then pops out. Electrical connection was obvious. The motor sping was the next most difficlt part. The spring fits on the rear part of the motor which is most easily accessed through the rear panel used for replacing the water pump. The water pump has three screws holding it and two hose clamps that come off easily with a pair of pliers. Before removing the water pump, I had to tip up the machine and take the belt off. This was also pretty easy. Put it back together and works great again on all cycles.

Remover agitator/Auger assembly. Install new agitator/auger assembly. Washer still would not agitate. Called repairman and found the transmission was bad. Fortunately transmission was still under warranty. 10 year warranty on transmission.

Removed upper back cover to expose the timer, the whole panel could then be tipped foward which made it easy to work on.
Removed the dial knob on front by popping off the cover then pryed up a smaller plastic button used to hold the knob in place.......knob slid off.
Disconnected wire harness from the switch.......had to pry up the snap tab that holds it in place.
Had to remove a small electrical board attached to the back of the timer......used screwdriver to pop it up and out (gently).
Removed one hold-down screw, lifted a little lock-tab and slid the unit to the left and lifted out and replaced.
I'm sure I forgot something.........but the whole thing was pretty easy to figure out .

I did what anyone could do, remove the screws and replace the part. The part just came apart during installation. If I were Maytag, I would replace the part free of charge.

Found a website that showed how to open the lid. Lifted the lid and checked the solenoids. When hot was disconnected, got cold only. Multimeter showed hot was being continuously energized regardless of temperature selector switch position. Removed back (5 or 6 screws) and found the circuit diagram. Studied it and determined that the switch or analog card had to be the problem. Took digital pictures of everything to aid in replacing wires pulled for trouble shooting. Pulled temp selector switch (pushed in a couple of tabs). Disassembled switch and checked all contacts. Working fine. Nothing left but the temperature board. Determining correct revision was difficult. Found a website that said, "first numbers of serial are revision number. Pick card with highest revision number lower than your model." Replaced card and everything worked as designed. Every wire was labeled and every wire bayonet was labeled so I didn't need the pictures, but I felt better having them.

Took a screwdriver and pried up the top of washer, then reached in and unscrewed the front two screws that allowed the front to be lifted off.
Removed two screws on lower right side that allowed us to pry open right side of washer. There are six springs along the bottom of washer that keep the tub stable and keep it from bouncing against sides while in spin mode. One of the springs broke and needed to be replaced. Off course it was the one that was in the far back and the hardest to get too. But by prying open the right side it was reachable. The wife pushed against the tub to make the spring stretch a little less but still was too difficult. We took the advice of another home repair guy and put quarters in the spring (about $1.75 worth) to make it stretch out, then it was simple to connect the two ends, remove the quarters and voila....it was done. Screwed theright side back on, but the minimum order on the springs was six and the others seemed fine, we just put the other five inside the washer cabinet, replaced the front panel, reset the clamps on top of the front panel, slammed the top down and we were back in business. The parts including shipping was a little over $10.00. So I am sure we saved at least $140 repair job.

Vey Easy to Fix. 1)Turn Water off at the wall. 2)Remove access panel on back of washer. 3) Remove Water pump. It is bolted down to the bottom of the washer by three nut head bolts. when loose the pump can be manipulated and tilted so the belt will have slack and most likely fall right off. Have a bucket ready. Remove water hose from top of pump by sgueaing clam with pliars and sliding clamp up hose. allow to drain in bucket. Lift drain hose out from wall and allow to drain through the pump into bucket. remove hose from pump that goet to drain. Replace pump and reverse steps listed above.