MAH21PDDWQ Maytag Washer - Instructions

Replaced drain pump and drain hose.

Replaced it with the new inner dooor.

Ordered a new inner panel and had my son in-law put it in for me. He is a mechanic so it was a quick an easy fix.

removed front of washer. loosened two hose clamps. replaced hose. tightened clamps. replaced front cover.

Removed the door from the washer and removed the screws holding the broken door panel to the outer door. Removed the clips that hold the screws in and transferred them to the new inner door panel. Removed the drain pipe and gasket (I assume that's what it's called) by unclipping the bottom from the door. There is another metal ring that had to be unscrewed. Then we screwed it to the new door panel and installed the gasket and drain pipe. Attached the new inner door panel to the outer door and screwed the door to the washer. Fairly easy repair.

I just replaced the pump.

The repair was very easy after watching the video that was with the part. I will continue to use this site for other repairs that need to be done.

Replaced the belt and motor isolators. Watching your video made it very easy.

What transpired was removing the guts from the old inner door and putting them onto the new door which extended the time. Not sure about the tools because my handyman/friend did the installation while I was gone. He was a little frustrated with it. Otherwise, the door fit well. We decided that using hot water was the problem with the water leaking from the door. Using cold and warm water settings seems to make a difference.

Basically the problem was the bearing replacement. Although you cant get them on PartsSelect, I got the seal kit on the site. The seal kit is easy, the bearings took two days and an air hammer to extract them and a big hammer to get them back in. All in all it was worth it,

I followed the video for the installation. I did find that installing the spring was no way as easy as it looked in the video. Otherwise, OK.

I lifted the lid, removed the front cover and then twisted the pump in its mount. The pump came out of the mount and i put a pan under it. I unscrewed the two clamps then pulled one end out. Water spewed everywhere and it was a bit of a mess. I pulled out the two wiring harnesses and pulled out the pump. It had a key, a quarter and a nickel in it. I had not seen the key in years! I put the ground wire on the new pump and then the main wiring harness. I put on the power wires but later had to take it back off, so do this later. I then attached and tightened the clamps. I put the pump in the mounts and then twisted it into locked position. Then i put on the power line. I put the cover back on and tested it, all good. I saved a lot of money, about $300 between the initial service call and second trip to install it. I like this washer because it gives you problem codes. It is 14 years old, and this is its second breakdown. First time was the PC board under warranty. No problems for 12 years, which was caused by leaving coins and keys in the pockets of my clothes.

Parts Select suggested the fix with a 99% rating that it was the drain pump motor. When I got the old pump out it was clearly not working. It took 4 days to get the part, but after getting the part it was just plug and play.

My husband, a mechanical engineer, kept forgetting to take all the brackets out to hold the screws in place and therefore had to take it apart several times to put the brackets in. Difficult time getting some of the parts out of old door to use in new one without breaking them as most were made of plastic. Washing machine works fine now.

I bought the new Lip Seal Kit thinking that the sound I was hearing had to do with it sticking inside the drum at the end a rotation in either direction. We had replaced the outer drum a few years back when the bearings went. Believe me, you will know when your bearings are going. It sounds like you are in the same room with a jet engine. I knew this sound was not from the bearings. I had the washer apart in about fifteen minutes...and yes, I am a 125 lb. female...so ladies, it is not an impossible task. I have taken that washer apart enough times before that it is no big deal. Just make a mental note as to how it goes back together....if all else fails one can look at diagrams online. My husband just stood there and said "nice job honey". After I got the old seals out and the parts cleaned up, I turned the bearings to make sure they sounded smooth. A-okay. I installed the new seal and smoothed molycote on the spider shaft; replaced the drum, front panels, etc; tightened the pulley with a torque wrench, belt on, etc. and.....turned on the washer. The sound is still there. Sooooo, I am fairly confident that it comes down to the belt and the motor isolators...mostly the isolators...belt is pretty secure. I am changing those tomorrow. Found someone on youtube with the same problem...only far worse...and a response posted said it probably was due to the isolators and belt. Our seal wasn't too fried, but I guess that it isn't a bad thing that I changed it anyway since it has been a few years and they do fail resulting in bearing damage. Better to catch it now. As for whether my machine is worth fixing at its age, I went shopping while this was going on and I don't trust anything out there to not have a multitude of problems. At least with my current model...that still looks like new btw...I don't have a learning curve to deal with on how to take it apart. And a great big shout out to my father who taught me how to dig in my heels and get my hands greasy!! Update: Replacing the motor isolators did the trick. Put on a new belt too as long as I had the back panel off again. Running like a champ!!