PAVT234AWQ Maytag Washer - Instructions

I checked out your other repair information and deided I could do this. Ordered the part and it as her several days before I expected it.

Ok, let's do this thing.

MAGIC TOOLS:
5/16" socket or wrench and #2 Phillips screwdriver and something to remove hose clamps - I recomend a 6" to 8" vice grips and a 6" to 8" plires.

1. Pulled the washer out in the middle of the floor and disconnected the hoses and removed the rear access cover, disconnected the pump hose, released the top using a 1/8' common screwdriver in that narrow space between the top and the front panel. Removed the 2 screws holding the front panel on and removed the front panel.

2. Disconnected fill level hose- toward the left rear side - turned the machine on it's side and walked the drive belt off, tipped it back up right and removed the 6 springs - be sure to note their orientation and location.

3. Lifted the whole assembly out of the top of the machine and set it upside down next to the machine.

4. Loosened the screws holding the snubber in place - NOTE I did not remove the screws - loosen them sequentially little by little untill you can get the snubber to come out. I did not remove the pulley as my Craftsman ratchet and standard - short - socket allowed me to get between the pulley and the screws to loosen them.

5. I removed the old well worn snubber, cleaned the area up and the new snubber actually fell into place and I retightened the screws in the reverse order until they were solid feeling.

6. I lifted the assembly back into the frame, reconnected the springs and the pump hose and the fill level hose. I reinstalled the front cover - AND HERE IS THE IMPORTANT PART!

7. You are so happy this is going so well that you forget to put the BELT back on before you hook up the hoses, so you have to unhook the hoses to put the belt back on and then rehook the hot and cold hoses and drain hose again.

8. Except for number 7 this is a piece of cake. My only concern is how often will I have to do this. The machine is only 8 years old.

I tipped the washing machine back to allow me access to the bottom of the washing machine to remove the belt from the water pump. After removing the belt, I righted the machine, unscrewed the three screws holding the rear access panel on. I used pliers to remove the clamps from the inlet and outlet hoses then removed the hoses. I removed three screws holding the water pump on to the bottom panel of the washing machine. I removed the pump and replaced it with the new pump. I then reinstalled the screws, the hoses, the clamps, the access panel, and the belt. I plugged the washer back in and - viola! It works again.

I wasted time opening up the metal container for the washing machine, which was easier than expected. The top simply pops off with a little bit of prying with a screwdriver, then the front panel is held in place with two sheet metal screws. The front panel then lifts off and you can see the exterior case for the tub drive mechanism and motor. But, it wasn't obvious what was wrong until I tilted the entire unit backwards and saw the drive belt available directly under the machine and fully accessible without any tools. It was obvious, because there was a 1/8" worth of belt fragment dust under the machine. A new belt was all it needed and after I ordered it from PartSelect, I simply jimmied the old belt off the main pulley and put the new one on. It no longer squeals or slips. Hopefully, I gained another 5 years of life out of the washing machine.

I could not tell where the leak was coming from. It was intermittent. Also the clothes were not getting totally dry in the spin cycle. Finally the drum stopped turning. The bearing in the waterpump was shot and the water was leaking from the waterpump. Luckily or unluckily, the bearing completely went and I then found out that the intermittent leaking was coming from the pump. I replaced the pump and the belt that was damaged when the pump bearing locked up. This has resolved the leaking issue.

I took the front pannel off just 2 scrwe was holdig the pannel,the motor was in ftont,4 bolt was holdig the moto,and it is very easy to change,

Noise loudest during spin cycle. Wash cycle showed transmission was ok. Pump shaft loose in housing. Fix was just as described. Tip washer up, lift belt from pulley on pump. Remove rear panel access. Remove hoses. Un-bolt pump. New pump does not have metal base plate, it fits directly to base of washer. Bolt new pump to base in same orientation, attach hoses, tip washer up and slide belt back on to pulleys. Move belt by hand to check function. Reconnect washer to utilities and begin fill. Check for leaks at hoses. Replace rear panel cover.

I tilted machine onto the front to acces the rear panel. i removed the three screws to expose pump, took of the drive belt located under appliance, removed the three pump screws and removed old defective pump. I installed new pump, put the drive belt back on, reinstalled back panel and screws, hooked the appliance up and started. Been running great ever since. Entire process too about 10 min.

No need to buy a brake wrench nor the expensive spring remover. Once the drum is out the washer turn it upside down and loose the screws holding the transmission about a little more than half way, to give the new snubber enough room to fit in, them tigh and assamble everything back together

Obvious problem: belt destroyed. The plastic pulley on the motor was damaged beyond repair. Since you can't replace just the plastic pulley, you have to purchase another motor. The machine still would not spin. Checked the pump again. The bearings might be bad. Replaced pump; Success! washer works again. Total repair: belt $15.68, new pulley with motor $132.00, and new pump $80.00. Estimated cost to repair about $228.00. Time to troubleshoot. 1 hour, time to fix 1 hour; Total time in labor about 2 hours.

Remove front panel and back service panel below water conn. lines. Put a 4" plastic box between the tub and inside of cabinet "directly opposite the spring to be removed to lower the tub to base for less opposing travel to unlatch spring from tub hook. Also took an old slotted screw driver w/ a blade about 1/4 " and grinded 1/8 from middle about an1/8" deep and used it to latch the spring when pushing it up and off the tub. Replaced all 6. Also did motor pivot spring. Tested and the it worked for one cycle, then the tub again just falls to the right as if the spring at 9 o'clock was broke and strains the belt drive but the spin cycle still works o.k. and the washer does not bang and walk away till you stop the machine. Thought the 6 tub springs would take care of both problems. Told that the snubber ring needs to be replaced. Never but another maytag again. JUst did the belt,a week later the water pump went then the springs.....

I simply emptied the machine of all the water, tilted the washer on its side,removed the small gray access panel located on the back of the washer, removed both hoses and the drive belt. Then I removed the three screw bolts that hold the water pump in place. Then I replaced the old pump with the new on by just following the process in reverse. I did notice that the new pump did not come with a metal support plate(at least thats what I called it. No problem though when I found out from a local repairman that its a newer design. Total time less than 15 minutes.

I opened the front of the machine. The clips had rusted. One broke and the others were very difficult to work with. I pried the panel open with a large screwdriver. I took the back panel off to access the water pump. I removed the back panel on the electricals to access the timer. To replace the timer I pried off the decorative cover. To get the knob off you have to squeeze in on the timer split shaft while pulling out on the know. This was the second hardest part. (The front panel access was the most difficult). After that the timer clip is easy to loosen and it slides a littel then pops out. Electrical connection was obvious. The motor sping was the next most difficlt part. The spring fits on the rear part of the motor which is most easily accessed through the rear panel used for replacing the water pump. The water pump has three screws holding it and two hose clamps that come off easily with a pair of pliers. Before removing the water pump, I had to tip up the machine and take the belt off. This was also pretty easy. Put it back together and works great again on all cycles.

I took the bad water pump off installed the new one and hooked up the new drive belt. Overall it took me twenty minutes, not all that hard to do.

Diagnosed that the snubber had failed.
Removed the belt, cam assembly and pulley assembly. Using Maytag brake removal tool #12002012 I removed the brake stator. I removed the front of the washing machine and the rear access plate. I removed the six tension springs. I moved the machine basket and shaft assembly toward the top of the machine. I removed the old snubber and replaced with a new one. I installed 6 new tension springs and reassembled.
The washing machine runs great.

Vey Easy to Fix. 1)Turn Water off at the wall. 2)Remove access panel on back of washer. 3) Remove Water pump. It is bolted down to the bottom of the washer by three nut head bolts. when loose the pump can be manipulated and tilted so the belt will have slack and most likely fall right off. Have a bucket ready. Remove water hose from top of pump by sgueaing clam with pliars and sliding clamp up hose. allow to drain in bucket. Lift drain hose out from wall and allow to drain through the pump into bucket. remove hose from pump that goet to drain. Replace pump and reverse steps listed above.