MAH21PNAGW Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Morgan from GARDEN RIDGE, TX
- Parts Used:
- WP22003275
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
leaky door
replaced inside of door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from HOUSTON, TX
- Parts Used:
- 12002039
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench set
Had Hurricane Harvey water high enough to short out control board and soak motor.
Used the conversion kit to replace both parts.Note the supplied instructions say to test the install by running a spin cycle before you put the door and panels back on. However the unit will not initiate a spin cycle without the door lock engaged. Not just the light switch, the actual door lock mechanism. You have to reinstall the door, then test. This error in the instructions cost me about 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jodi from Ringle, WI
- Parts Used:
- WP22003275
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Leaking front door~cause: hamper wires wriping inner plastic door liner
Removed door, changed over parts from one panel to the other, then rehung door....extremely easy! Thanks for the part!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Warwick, RI
- Parts Used:
- WP22002798
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door hinge worn.
Very easy.I used a screw driver to remove and install the new hinges. Three screws on each hinge. Door closes like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Bozeman, MT
- Parts Used:
- 12002533
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set, Wrench set
Boot torn on frontload Maytay Neptune Washing Machine
With a torn boot on this front load washer, (nails in the pocket of my jeans) water leaked out on the floor with every wash. I knew it would cost a fortune to get fixed, so I decided to try it myself. I can take anything apart!
I heard of Parts Select.com from a friend and checked it out. With their help, I found the model and part and just ordered it. It was easy!
When the part arrived, I was obligated then to do something!
Since this is a stack unit, with the dryer on top, I thought I would take the dryer off and try the repair from the top. But there was no way that dryer was coming off! I tryed every screw and it wouldnt budge.
So I saw two screws in the front and started in on the washer below. I was careful to make notes on how I took this machine apart so I could put it back together!
I got down to the drum with a spring close guywire that holds the boot tight to the drum. It came off easily and I took the old torn boot off and put the new boot in place.
The tough part was getting that guywire and tight spring back on! The lip that holds the boot to the drum is very shallow and the book would not stay on all the way around and allow me to string the guy wire around in the little channel without coming off. FRUSTRATING!
I improvised and used duct tape to tape the boot to the drum to keep it in place so I could string that wire around. Man, did that take some doing!
I managed to get that wire around with the help of the duct tape, but the second big challenge was putting the spring on, as it was under alot of tension. It was tough to puuuuuullllll it together without pulling the boot out of the channel I had to duct tape it into!
By the grace of the Almighty, some prayer and some cussing (forgive me Lord), I got the spring into the rings on both ends of the guy wire. VICTORY!
Putting the boot front back in is easy, just put it into the holes that receive the projections under the front of the boot. No problem.
After all that, putting the washer all back together was a cinch!
And....
IT WORKS!!
I did it! No more leak! No expensive fix it job!
I did it myself, am prouder than heck!
Oh.....
No more Nails in the jean pockets!
I heard of Parts Select.com from a friend and checked it out. With their help, I found the model and part and just ordered it. It was easy!
When the part arrived, I was obligated then to do something!
Since this is a stack unit, with the dryer on top, I thought I would take the dryer off and try the repair from the top. But there was no way that dryer was coming off! I tryed every screw and it wouldnt budge.
So I saw two screws in the front and started in on the washer below. I was careful to make notes on how I took this machine apart so I could put it back together!
I got down to the drum with a spring close guywire that holds the boot tight to the drum. It came off easily and I took the old torn boot off and put the new boot in place.
The tough part was getting that guywire and tight spring back on! The lip that holds the boot to the drum is very shallow and the book would not stay on all the way around and allow me to string the guy wire around in the little channel without coming off. FRUSTRATING!
I improvised and used duct tape to tape the boot to the drum to keep it in place so I could string that wire around. Man, did that take some doing!
I managed to get that wire around with the help of the duct tape, but the second big challenge was putting the spring on, as it was under alot of tension. It was tough to puuuuuullllll it together without pulling the boot out of the channel I had to duct tape it into!
By the grace of the Almighty, some prayer and some cussing (forgive me Lord), I got the spring into the rings on both ends of the guy wire. VICTORY!
Putting the boot front back in is easy, just put it into the holes that receive the projections under the front of the boot. No problem.
After all that, putting the washer all back together was a cinch!
And....
IT WORKS!!
I did it! No more leak! No expensive fix it job!
I did it myself, am prouder than heck!
Oh.....
No more Nails in the jean pockets!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Springfield, IL
- Parts Used:
- 12002533
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Moldy Door Boot
My husband completed the repair by himself. He said that the "string trick" was helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rex from Clearwater, FL
- Parts Used:
- 12002533
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Nasty Mold (standard Maytag issue)
Removing the gasket was very easy. A couple hints on installing (1) attach the gasket to the drum first!! this is the trickiest part but once you get it on, attaching the cable and spring was fairly easy (just used two people and a pair of needle nose pliers). Once you get that on, "lube" up the other side with soap to make install easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tina from Stanton, IA
- Parts Used:
- 22002266
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
purchased a front load washer, missing siphon cap
Ordered siphon cap according to FPS parts list. Wrong cap, but I don't care! Customer support was so helpful and willing to do everything to get me the correct cap, to include refunding my purchase price AND shipping before I even sent it back. They will be my first choice for parts in the future! My husband is a "fix it" guy, so I know that will mean a lot of purchases. I look forward to future business with this company!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sudie from Ocala, FL
- Parts Used:
- 22002266, WP22002265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing parts
Our rental house washer had the parts removed by the last tenant, just replaced them. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from amston, CT
- Parts Used:
- WP22003262
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
leaking water
removed one panel and front door to access under tub.leak solved!!!! thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Oceanside, CA
- Parts Used:
- 12002533
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Moldy Bellow
removed door,Opened the front panel, opened the top and proped it out of the way. Pulled the boot from the front cover disconnected the drain, released the boot clamp and pulled the boot off. I cleaned the inside of washer and soap tray. cleaned debris from the drain hose. repaired a broken soap dish connection. changed supply hoses and new valves. Generally checked cleaned and overhauled the washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Westminster, CO
- Parts Used:
- 22002266, WP22002265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing these parts
Bought the parts and just inserted them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Jupiter, FL
- Parts Used:
- 12001413
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Deteriorated and clogged strainer; slow water fill.
Loosened the hose coupling, removed the old washer and strainer; cleaned the opening; flushed the opening; installed new strainer and washer; reattached hose and "Bob's your uncle"! No problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Rolla, MO
- Parts Used:
- 12002533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Bellow was tore and falling apart
Wow! Thanks to the customer info/hints already posted the repair went super smooth and was relatively easy to accomplish. $70.00 for an easily replaced part sure beats $1,000+ for a new washer. Super fast shipping reduced down-time significantly!!! From start to finish the job took less than 30 minutes. Thank you so much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Bandon, OR
- Parts Used:
- 12002533
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
mold spots
Off with the door. Off with the front panel. Lift the top and you are looking at the boot. Remove the boot retaining wire . Remove the boot and reverse the procedure. It's a snap.
Was this instruction helpful to you?
Thank you for voting!