SAV5701AWQ Maytag Washer - Instructions

Found out that these switches go from time to time and are usually the culprit when the washer won't operate. Opened the cabinet facing. Warning: there are plenty of YouTube videos on opening Maytag washers. None helped me with this model. I ended up finding the screws to open near the floor on front. Once it's opened, just replace the faulty switch, reconnect and you're in business. Getting the washer opened was about the hardest part of this repair. Total cost: Less than $30.

We noticed that water was on the ground of the laundry room. We initially thought that the washer was leaking. Realized that the washer was going on the spin cycle without draining the water which caused the water the slosh over the edges and then leak on the floor. Well, I had to remove all the wet clothes and suck the water out with a shop vaccuum-this actually took most of the time. After taking the front of the washer off, we noticed the water pump was stripped out. After removing the pump, we then noticed one of our kid's socks jammed in the pump. How the sock got there is still a mistery. We found the replacement part on PartSelect and ordering was easy and fast. Thanks. We're washing clothes again.

Wow! My husband and I researched the problem online and ordered the part after reading from others how to take the machine apart. We are very unhandy, so we felt quite an accomplishment fixing the drain hose with rubber elbow ourselves! Thank you for the diagrams that so clearly showed the part we needed to order.

I was at work but a friend of ours and my husband did the repair. But what I was impressed about is how fast we got the part. thanks a lot

replaced belt that was wore out. decided to replace pump while I had washer apart.

remove front cover disconnect water supply remove hose clamp,take drain line replace with new hose reconnect water supply replace front cover job complete.

Disassembled washer as per directions with seal kit. Removed inner tub. Cut both tub shaft bearing in half; punched out from outter tub. Installed new bearings using .5 inch threaded rod, washer and bolts. Installed new seal on inner tub shaft. Installed inner tube. Re-assembled washer.

The hardest part was removing the tub from washer by myself. I simply removed the bolts holding the sides to the bottom of the unit and lifted it straight off. Be careful when you remove the springs from the drum so they don't spring back and puncture the drain line. Thank you RTV gasket maker. Once the drum was free from the base, i tilted the drum back exposing the pump housing. I used a pair of pliers to remove both drain lines then removed the 3 hex screws freeing the pump. I had no problem removing it from the motor shaft, it slipped right off. I put everything back together as easily as it came apart.

After pulling front lower panel off, disconnected idler pulley spring and left side tub stabilizer spring to allow room to get motor out the front. Took belt off transmision pulley, unbolted 4 motor mount bolts, dropped the motor/pump assembly down and disconnected the electrical plug (motor). Took motor/pump assembly out, flipped it over, unbolted 3 pump bolts to remove old pump, which came right off. Then reversed the whole process. Pretty straightforward, just time.

removed motor removed belt replaced belt,spring,idler wheel, slid back motor in 4 bolts,plug in motor, run good on test run

Parts where in, in a timely manner. I remover the fabric softener cup on top of agitator. User a 1/2 inch socket and a 3/8 ratchet with an 8 inch extension to remove the center nut. Popped the agitator out. Installed in reverse order, only tightening the nut slightly. The install went just like the video. Thanks much.

Cleaned the grooves well on the top of the agitator and put the new dispenser on. Easy! I suffered with the old one coming off in the spin cycle for too long. Once I located this site it was relatively easy to find the part & order it, and it arrived quickly.

Purchased x4 new adjustable legs. Leaned the washer back and held in place with block of wood. Loosened the two older front legs with an adjustable wrench because they had a locking nut and replaced with new legs. Repeated process on back side of washer. Once all the new legs were installed leveled the machine adjusting the legs if necessary.

The new hose was exactly like the one I removed. It was simply a matter of putting the new hose through the back, replacing the hose clamp, take the piece off the old hose that makes the bend in the hose to go in the wall drain. Replace the lower front panel with two screws and I was done.

You tubed this procedure and it took 20 min.