LAT5004BGW Maytag Washer - Instructions

Found instructions at this web site, got part in a couple days, changed Lid Check Switch in 15 minutes, washer was up and running again. Best website for fixing stuff I've seen!

Loosened the set screw and removed the agitator, found nothing wrong. Replaced the agitator and tightened set screw, no more wobble.
This is a mid 1970 Maytag and a workhorse.Had three kids wash over the years, now "kids" in their late 30's and early 40' and washer is as good as new (except a little rusty)

First time I had a problem with it. Sometimes just look for the simple things !

Part select refunded me for my part that I ordered very fast.

Great Company to deal with!

Replaced lid switch, but problem still continued.

The machine had leaked late last year; replacing the interior hoses fixed it, but the leak came back.

To diagnose the problem, I used a short, #2 phillips screwdriver to remove the two retaining screws under the front panel indentation. I pivoted the front panel toward me, unhooked it from its retaining hangers, and set it aside.

Inspection revealed that water was running down the exhaust hose from the siphon break, so I unplugged the machine, pulled it away from the wall, removed the two top retaining screws and pulled the top toward me. There was enough play in the wiring harness to leave everything connected.

I used a socket wrench to loosen the hose clamp at the bottom of the siphon break, and to remove the 4 hex head screws that hold the siphon break to the back of the machine. A few twists freed the siphon break, and one glance revealed that its top was covered with soap scum. It clearly needed replacement, so I ordered the part.

Replacement was a piece of cake. I mounted the gasket in the new siphon break, moistened its tube, twisted it into the hose, and tightened the clamp with a socket wrench. I then mated the new part with the old exit elbow, lined up the holes, and installed the retaining screws. I pushed the top back into position, installed the top retaining screws with a socket mounted on a universal nut driver handle, rehung the front panel, and installed the two retaining screws. Presto, good as new!

Everything else is clean. I would much rather replace a few parts and continue using "Old Reliable" than pony up $800 on a new machine.

Removed the front panel with a screw driver, removed the old bumpers with a pair of pliers, replaced the bumpers and replaced the panel. All was very simple and took no time. The video on your website was most helpful. Thanks

Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.

I watched the video suggested by Part Select, it was easy to follow. I had first changed the belts because they were worn but that wasn't the problem, the next suggestion was the lid switch assembly which was the answer. This washer was produced in 1989 and works like new again!

It was really quite simple. I found out where the leak was coming from by taking off the front panel and running the washer through the drain cycle. PartSelect website was right on for what part I needed and delivered it promptly. The installation video from PartSelect couldn't have been more clear. I removed a few screws from the back of the washer and installed the new part in about 1 hour. All was good.

Started with removing 4 screws on the top of the control panel. Once open, I found the schematic taped to the top. I traced the wires and found the 2 wires to test. I unplugged them and attached the jumper wire. Turn on machine and it worked. Ordered the part( it came in in about 3 days. First disconnect the power. The micro switch is mounted with 2 screws, remove these and as you disconnect the wires , attach them to the new switch, put it back in place and reattach the screws. Test .

Chalked the transmission with a pipe wrench. Removed the brake with grabbing on to it with vicegrips and hammered on the vicegrips to remove the brake. The new brake spun on after the first two brakes didn't. Working great now!

Agitator motor burned out -- purchased new one through Parts Direct (parts still available) 4 bolts and plug and play wire harness and now runs like new.

I followed video instructions which were very helpful and getting to the lid switch assembly was not difficult. After putting it on we still had nothing. I noticed there was quite a bit a corrision on the connecters so we cleaned those with fine emery paper, reconnected them and like magic , the washer is back in business. I was very surprised the part arrived about 36 hours after I placed the order and in just a couple of hours at the most we had a working washer again.I've got partselect.com saved in my favorites for any future diy repairs needed.??

Followed the first guys directions.
remove front
lift top
remove agitator
remove locking nut clockwise
remove inner tub
remove Mounting S loosen set screw and clockwise also
clean well
replace boot as shown in tip in sheet
push boot on completely

After reading partselect.com and a few other web sites, I thught the leak was either a hose clamp, hose, or syphon break.

1. Two screws at the bottom front are removed,
2. Bottom front moved away from the machine unitl the top clips allow it to come off.
3. Remove 2 hex head screws from the lid (look up, use a nut driver or I used a socket.
4. LIft the lid from the front (similar to lifting a car hood)
5. Syphon Break is in the top back right.
6. 4 screws in the back and a hose clamp that connects to the pump.
7. Put it all back together in reverse.

I had considered replacing the hoses while I was at it, but they all looked fine. Suggest you order the Syphone Break "Kit" because it contains clamp, and ring gasket that is between the break and the discharge elbow.

Works Great! Saved myself at least $150 in service call and parts markup.

First I bought a Maytag spanner wrench on eBay, you have to have it. It was $12.00 including shipping. Then when the parts showed up the next day followed the video and had it done in just under an hour from gathering my tools and cleaning up. The video was perfect and I had no troubles what so ever. The quote from the repair services was $280.00 and I did it for less than $90.00