LAT2600AAE Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken Belts
Lets just say thank god for part select!!!! # 1 By far. This was a one two three job.
Was this instruction helpful to you?
Thank you for voting!
Repairs Were Easy.
Removed top. Removed agitator and tubs . Replaced seals and reassembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- justine from NEWARK, NJ
- Parts Used:
- WP6-2022030, WP213045
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
pump and hose leak
Easily
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from ATASCADERO, CA
- Parts Used:
- WP22004243
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Washer would not start or fill up.
First of all unplug the washer and turned the water off to the washer. I second removed to back plate from the top control panel. Third using a 10mm nutdriver removed the two screws holding the control panel to the top of the washer, slid the control panel toward the front and flipped it out of it's grooves. Fourth unplug the lid switch. Fifth slide the old switch forward, up, and out. Finally replaced the new switch and lined the push button on the switch up with the lid detent switch. Plugged the cable switch back in, turned on the water, and plugged in the power cable. Tested the washer to ensure the switched was lined up correctly. Once the water started coming out. I turned off the machine unplugged the washer and finished reassembling the control panel. All in less than 10 minutes and SAVED myself over $130 for a service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EL from O'Fallon, IL
- Parts Used:
- WP211726
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Resin balls on which the top loader lid hinges had broken.
Cleaned the cavities. Lubed them with olive oil. Inserted one ball on left side, while holding tension against that side to hold the ball in the lid and top indentations. Applied olive oil to right hand side indentation, and placed the new ball into lid indentation. Put lid down into closure cavity with ball, and with lid vertical, began pushing it rearward so as toslightly spring metal lid rolled edge and top metal away from one another UNTIL the new ball snapped into the hinge indentation in the machine cover. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Madison, NJ
- Parts Used:
- WP213045
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washer leaking at the front.
Our Maytag (A308) washer is now about 29 yrs old. I put in a PartSelect water valve 3 yrs ago. When it started leaking recently I found the cuplrit to be a flexible hose to the outer basis. The front came off easily (two screws at the bottom) and the hose clamps required some cleaning. I recommend purchasing new clamps. Under 30 minutes to get it running again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elzo from KALAMAZOO, MI
- Parts Used:
- 12112425
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
old belts slipping squealing, rubber shavings on floor.
Pull washer out from wall. Remove front panel (2 Philips head screws), swing bottom of panel out, remove panel. Tilt washer backwards, lean against wall to expose area under washer. Roll off old belts, roll on new belts. Move washer back upright, replace front panel, replace the philips screws, move washer back to original position.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norman from LAKE ZURICH, IL
- Parts Used:
- 12112425
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Agitator was not agitating. Thought it was stretched/worn belt. It was not! Transmission is shot!
Could not repair. The gearbox on the agitator was broken and that kept the agitator from working. Do not assume it is a belt problem on a washer built in 1987.
Was this instruction helpful to you?
Thank you for voting!
pump and drive belt was thorn
Installed drive and pump belt.. very very simple. only tool required was a screw drive to remove front panel of the washing machine.
Was this instruction helpful to you?
Thank you for voting!
burning smell from washer
Replaced both the drive belt and pump belt in less than 10 minutes. Maytag has the easiest machines to work on.
Was this instruction helpful to you?
Thank you for voting!
broken belt
Layed the machine on it'sback and put the 2 belts on the pulleys,Very easy ,when you know to put the machine on it's backside!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Dunellen, NJ
- Parts Used:
- WP22003363
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Waher timer gets stuck on
Ordered part overnight. Came the next day. Tillted the washer foward 3 screw to remove back panel,popped off the knob and intalled new timer. Good for another 8 years!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from ANKENY, IA
- Parts Used:
- 12112425
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
smelled like something smoking
took front panel off had 2 screws, propped up washer in front, took belts off with hands and put new ones on in reverse order One belt was badly cracked. I am 77 year old female, if I can do it, anybody can. great service on getting belts too. Thank you
Was this instruction helpful to you?
Thank you for voting!
No tub spin, burning smell.
Partselect.com gave me a very helpful list of parts per symptom. Said that there is an 88% chance that belts were my problem. Since the machine is 200 miles away I ordered two other parts as well. Belts fixed it! Took front cover off (not totally necessary). When the machine is tilted back belts are exposed underneath. Two belts later I was up and running. This site is really great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from NASHUA, NH
- Parts Used:
- WP89503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Leaking water inlet hoses.
Removed the old hoses and screwed on the new hoses.
Was this instruction helpful to you?
Thank you for voting!