Models
>
FAV6800AWW
FAV6800AWW Maytag Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for FAV6800AWW
Viewing 9 of 9Manuals & Guides for FAV6800AWW
Click to downloadKeep searches simple, eg. "belt" or "pump".
In Stock
$149.05
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
In Stock
In Stock
In Stock
$8.00
This high pressure inlet hose washer is black. It is an inch in diameter, made of rubber, and used with many washing machines, refrigerators, and dishwashers.
In Stock
Special Order
In Stock
In Stock
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for FAV6800AWW
Viewing 3 of 3Leaking
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Deborah from Westfield, MA
- Parts Used:
- WP25001052
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Old Pump Stopped Draining The Machine- Impeller In Pump Wore Out
First- I unplugged and completely drained machine of water by putting hose at ground level near drain . Second- removed back plate to washer saving all hardware. Third- disconnected in and out hose to pump. Twisted pump gently as to pop it out of slots in bottom of machine. Fourth- disconnected wires to old pump hooked to new pump
... Read more
replaced pump, replaced hoses- tested machine then replaced back plate of machine. Done.
Read less
Was this instruction helpful to you?
Thank you for voting!
Belt Broke
Luckily, I found someone else with the same story, and read that you need the clutch assembly and the belt at the same time. One night when we started the washer, it made a metal seizing type squeal. There was smoke everywhere. After opening the washer, the belt burned through but the clutch had also seized which was the cause. Replace
... Read more
d both. Needle bearings were totally rusted. Must be leaking water somewhere. Just lift top, remove front cover (two screws inside the top). Prop up and secure washer. Loosen the motor bolt. Through the hole in bottom, fit socket to hex bolt on clutch. Our belt was already off as it broke in half. Remove clutch, slip new one on and make sure it goes all the way back on transmission. Place the one bolt back on. Two people are helpful here! Place new belt on grooves of motor pully (while person 2 holds the agitators still) and then work belt down and around clutch. Ours was a tight fit! Have a person pull back on motor as you tighten the one bolt you loosened. There is an in/lb rating on clutch bolt. Put washer back down and panel back together. Pretty easy repair to save tons on a new washer.
Ordered parts on a Friday at 3:05 pm, and they were delivered the next day! Excellent service!!! This saved our day!
Ordered parts on a Friday at 3:05 pm, and they were delivered the next day! Excellent service!!! This saved our day!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Drake from Crofton, MD
- Parts Used:
- WP25001052
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Broken Pump
Roll washer out of drain pan on section of 3" PVC pipe. Unplug washer & disconnect hoses. Remove rear access panel with nutdriver. Disconnect wiring harness from pump. Disconnect hoses from pump using screwdriver and pliers. Twist pump counter-clockwise to separate from bottom of washer housing. Transfer electronic component from old
... Read more
to new pump. Install new pump in reverse order as above.
Read less
Was this instruction helpful to you?
Thank you for voting!