LAT8200ABX Maytag Washer - Instructions

Great service! Part arrived within two days; installation instructions very
clear; washer back in service after15 minute installation. Thanks!

The hot water side would fill quickly but the cold water filled very slowly. The seloniods and the valve is built all into one unit. I ordered and replace the part in no time at all. Now both hot and cold water fill quickly.

Shut off water supply, unplugged washer power, removed supply hoses from old washer valve assembly, removed valve mounting plate and removed old valve assembly from mounting plate, diagrammed and disconnected hot and cold solenoid valve wiring and removed valve assembly outlet hose. Installed and connected new valve, performing the preceding steps in reverse order. pressurized new valve, verified valve function and checked for leaks and placed washer back in service.

My husband did this repair. He disconnected the old part, laying them out in the order that he took them off. He put in the new part and hooked up the hoses and we had a working washer again. I ordered the part and a couple of days later it arrived on our door step. Thank you for your speedy delivery. We live in a parsonage and the washer & dryer that were in here stopped working, so we brought our Maytags (used) from our camp where the problem occurred because of winter freezing. Thanks to Maytag for making this repair so easy.

I found that the water was coming from top of syphon break. Took it out located it on computor , ordered part. Took about 10 min to replace. EASY

First I remove the hot & cold water hoses using an adjustable wrench. I then unscrew the panel that holds the water inlet valve using a nut driver. I then carefully pull out the panel, moving the harness wires out of the way, so that I can loosen the clamp holding the inside rubber tube. I remove the old water inlet valve from the panel by removing the 2 screws and then put the new one in. I then reconnect the rubber tube and tighten the clamp. I then screw back the panel and reconnect the hot & cold water hoses. It took me about 20 mins to complete the job.

Pushed machine out from wall; disconnected the supply hoses (after closing the valves at the wall); unplugged electrical cord; removed two wires from the solenoid connectors; removed two screws that secure valve assembly to backplane of machine. Installation of new assembly was the opposite procedure. We have private well, and silt was plugging the cold water side of valve. So, I also installed a large sediment filter behind the washer, so this will never happen again.

open top of washer
remove two screws that hold water inlet valve
disconnect four wires and hose;replace new water inlet valve and reversed operation
everything went well

Removed front panel, removed bolts from the front of top panel, lifted. Removed hoses, then 4 screws from siphon break at top right rear of machine, removed siphon break. Installed replacement siphon break and secured with screws. Put some dish soap in hoses and slid them into place and tightened clamps. (It is necessary to move the top panel up and down at various times in the process to do all of this.) Then secured the top with the front bolts. Then installed front panel. Tested the machine, no leak.

Did the same as others. Loosened the three screws diconnected the wires and put them on the new valve. Disconnected fill hose and connected to new valve. 10-15 minutes. Replaced panel and tested new part. perfect, My repair was a little longer, I vaccumed up all the dust bunnies I could find before moving washer back. Good for another 35 years, I hope. Thanks for the help and experiences.

Solved theprobel m by noticiing the HOT water filled the tub and it began to run when it was full. Figured out it was the solenoid valve. Ordered a new one. Simple to install and then it ran just fiine.

Washer is enclosed in a walled partition. I spent more time moving the washer out so I could get to the back of the machine. Due to Maytag's design of a removal sheet metal panel holding the valve the entire water valve replacement was performed outside of the machine. The replacement valve was an exact duplicate and made it a simple swap out. More time was spent removing inlet hoses and outlet hose then in actual valve replacement.

First turned off water and unplugged washer. Removed hoses and then removed bracket. The new part needed the bracket from the old mixer which was no problem - 3 screws. Removed electrical plugs from old mixer-placed on new one.No problems - worked like new. Thanks for your prompt shipment and the good illustrations of the parts when I was searching.. Also, half the price of local parts houses and it would still have to be ordered.

Removed door panel to get to the electric control conponents and noticed a burned wire to one of the door microswitches. Ordered the door switch repair kit from PartSelect. Also, ordered and replaced the thermal fuse at the same time since it was only $12 and didn't know if that blew at the same time the switch cooked. I had the parts coming standard delivery (3-5 days), but they arrived the very next day. Parts included easy to follow directions.Job went pretty smooth and the dishwasher works again Good experience!

Took out 2 5/16" screws and loosened top and took off two ground wires and 2 hot wires for cold & hot water solenoids and removed & replaced solenoid wires and fill hose. Also Had fantastic delivery of parts.