MAVT734EWW Maytag Washer - Instructions

Turned off the water supply. Removed clothing and bailed out water fro tub. Removed back access panel. Turned washer over to access the bottom and removed drive belt by turning the large pulley attached the drum while pulling the belt over the pulley. Next remove the two hoses attached to the pump, remove the screws holding the pump on and remove the pump. Replace the pump by reversing the procedure, as for replacing the drive belt, place the belt on the motor and pump first and start it on the larger pulley and hold it on while you turn the pulley, it will pull the motor adjustment as you turn and when fully in the pulley it will be properly adjusted. Then replace the access panel, turn the washer upright, push back in place, turn on the water supply and replace the drain hose. Back in business. For me, while I was waiting for the new pump to arrive, I took the time to remove the agitator and tub and give it a good cleaning inside and out, but that's me.

A few youtube videos to replace the motor and belt. From there on out it was pretty easy. Separate the top from the spring clips. Remove front panel. Remove motor once inside and remove belt from underneath. After motor was out, Remove base from old motor and attach to new. Reassemble and voila. Good as new.

Unlike most videos, mine had a solid frame, no access panels. Following, is my disassembly & repair: I disconnected the water supply lines and drain hose. I slid the washer out into the center of the garage & removed the 9 base screws from the base plate. I slid the frame away from the base, leaving the working parts exposed. After pulling the working mechanisms from the outer frame, I turned it (drum, transmission & base) upside down. I used a pair of vise grips, pinched them onto each spring & removed them, using a downward motion it was a lot easier. I placed the base plate aside, removed 3 opposing screws holding the snubber ring & put 3 longer 8-32 screws in to hold the brake assembly. Then I removed the 3 remaining screws, lifted the plate & replaced the ring. Then I reversed the process, replacing the old springs with new ones & finished the job in about 2 hours.

As a 78 year old senior, I no longer have the upper strength and agility to remove the springs. Had to remove the washer casing (9 screws and 3 bolts), which gave me full access to r disconnect the springs, remove the tub, replace the snubber ring and reinstall the springs. The complete repair took me 6 hours, no assistance and was very thankful for the excellent videos available online.
Parts arrived in 3 days, fantastic delivery service, great prices and fixed my washer for $107.

Actually I got on YouTube and looked up the problem and watch the short video of it and went from there and it showed me how to take everything apart what the problems were and as I did take it apart and found out it was exactly what they said I simply reversed it just ordered the parts and put them in and took my time to make sure that everything was to specs as I've measured the clearance of the break and said all the hardware back in place it was quite simple yet it was just time consuming took me about two and a half hours but it runs quiet spins great just like a brand new one I couldn't be more pleased with it and I saved quite a bit of money doing it myself

Pump is readily accessible at the back of the machine by taking off the access cover. First step is to disconnect power and remove drive belt off tub pulley which is the largest in the center - the takeup is in the drive motor mount but it seems easier to turn the larger pulley and wind the belt off. There are three 3/8 hex mount screws fastening the pump to the washer base and two hose spring clamps attaching the tub drain hose and outlet drain hose to the pump. Follow the directions in the utube video which is the best (most others don't give detailed directions and best method). The only caution I would give is that there is some water in the drain hoses so be prepared to mop it up with sponge and bucket or have some towels available. Install new pump (loose assemble two visible screws to locate pump and then loose assemble far side blind screw and tighten all 3),replace hoses snug to stops and assemble clamps, replace access panel and replace drive belt and plug washer back in.

I first had to take the old part out to find out what the part number was. Then I went online and ordered the part. Once the part came in I attached to part and replaced the drive belt. I did not think it could be so easy.

I removed the silver cap and then removed the knob itself. I replaced the knob with the new part and also the silver cap with the part. The job was complete.

Removed it from the package and placed it on the washer.

Removed top, valve and water hoses. Replaced valve then reversed the process. Easy change out. Saved $100 service call.

Watching the u tube video associated with the part made the repair even easier. I’m very handy but gave me a better idea of what to look for and tools needed for the repair ahead of time.

This was a very easy fix.....roll belt off....roll new belt on....seemed to help not sure if it fixed problem....might try pulley and bearing kit next

Followed the excellent utube instructions you provide. Piece of cake when I followed the video. The rear springs became much more difficult because my model does not have rear access panel. They were the only stuggle. Thank you for doing the repair videos

Part Select data showed that over 60% of the time, this issue of the washer shaking was due to broken support springs for the tub and over 30% of the time, it was a worn/broken snubber ring. So, I initially purchased the six springs and snubber ($30 total) from this site and completed both of those repairs. I leveled the washer securely and tested it again. However, the washer still had the issue of shaking during the spin cycle with no improvement. So, I then researched again for this issue and parts recommended were a lower bearing kit or transmission. Since the transmission replacement was $429, that wasn't worth trying. So, for the $52 lower bearing kit, I ordered it from along with a new belt ($22) (even though the existing belt didn't show any signs of significant wear, but I changed it anyway). The new bearing kit was installed and the washer is now operating like new. I used the current videos on the website for replacing the parts that I ordered, and they were perfect step by step instructions. It made the repair very simple for anyone with any sense of do-it yourself ability and with minimum, ordinary tools. So, for approximately $110 for parts and doing the repair myself, the washer is like new again. Thank you!!!!

Shut-off water + power.With the putty knive; slide it under the front of the top to push back on the spring clips.The top will lift easily and it is hinged.The Water inlet unit in the back has a plastic cover.Remove carefully.One screw holds the unit in place. Remove and the the unit will slide out to the left. It's now easy to disconnect the hoses from the unit. The wiring to the coils is color coded,take note for proper reconnecting. Remove stakon connectors from the valve coils. Careful, do not pull on the wire but wiggle it of the coil connection.Pay attention to the routing of the wire harness. Also the kit comes with a clear plastic splash shield. make sure the new goes in the right place.Now the old water inlet valve can be removed from the metal bracket.One srew.Assembly goes in reverse