MAVT734EWW Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Florence, AL
- Parts Used:
- WP25-7220, WP22004333
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Hot water valve leaked by and then at last wouldn't open
Easy repair replacing the water valve assembly. Good advise from other posts helped much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BEN from DEXTER, MI
- Parts Used:
- WP22004333
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
would not stop dispensing water at any setting
followed directions you gave. Simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Cadillac, MI
- Parts Used:
- WP22002751
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lid hinge was broken causing lid to fall off when opened
Opened the lid and snapped hinge in to place. The part was an exact match and the job went flawlessly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Bethel Park, PA
- Parts Used:
- WP22004042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Fans on the Agitator had broken off.
I popped off the fabric softener on top of the agitator. Used an extended arm on my socket set to remove the only nut holding the agitator on the motor assembly apparatus. The agitator came off with ease. Just reversed the procedure in replacing the new agitator. This was an easy job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- danny from tallassee, AL
- Parts Used:
- 22004070
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
would not spin or drain
took the control panel apart by removing the 3 torx screws, removed the center insert from the knob and released the stem that holds the knob in place unplugged the harness, released the clips and removed the old timer. installed the new timer and plugged the harness in and installed the torx screws.
Thanks for shipping the timer so quickly, replacing the part was so easy and my wife is happy too.
Thanks for shipping the timer so quickly, replacing the part was so easy and my wife is happy too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from NEWCASTLE, OK
- Parts Used:
- W10814230
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Filled with water but would not start - Had to slam the door down
Removed the old part with a screwdriver & installed the new part. It took approximately 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from YUCAIPA, CA
- Parts Used:
- WP22004333
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Hot water would not completely shut off after a wash cycle.
Followed video on the website.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- emily from waco, TX
- Parts Used:
- WP22004042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
broken agitator
very easy replacement. was probably broken for a year and only took five minutes to replace. Can't believe we waited so long!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Sterling Heights, MI
- Parts Used:
- WP22003993, WP22003989
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Knob broke off dryer timer
The two parts purchased were the corrects parts needed to do the job. (There's always a first time for everything!) When the plastic timer knob broke away from the timer stem, it left the silver timer cap's locking pin embedded in the timer stem. I could not remove the broken remains of the knob while the broken off pin was still in place. And it was impossible to grip the pin with pliers or tweezers without damaging the timer stem. As a solution I grabbed my whole-house vacuum cleaner hose and sucked the broken pin out of the timer stem. Total time of repair was about 20 minutes not including the two-hour brainstorming time-out that led me to the vacuum cleaner solution.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BARDELL from BASTROP, LA
- Parts Used:
- WP22003483, WP21002026, WP21001598
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
replaced the snubber ring / the belt / springs
As for how I did the repair , I just followed your instruction video . The instruction video provided by Part Select was very very valuable.
The snubber ring was a piece of cake BUT would have been really difficult without the helpful hints in the video like replacing three of the screws in the rings collar with three longer screws so as not to disturb the spring under it.
The suspension springs were a bit more trouble since my washer doesn't have an access panel on the back however THANKS TO YOUR TIP to stretch the spring and put coins between the coils made this much easier . I don't know many guys that are strong enough to lay down and reach through the front and put those springs on the back.
Of coarse the belt was easy.
I also really like you list of probable solutions to the problems with the machine.
My wife is now happy with her washer again therefore I am also happy.
Thanks so much.
I can see me being be a loyal customer for many years to come.
The snubber ring was a piece of cake BUT would have been really difficult without the helpful hints in the video like replacing three of the screws in the rings collar with three longer screws so as not to disturb the spring under it.
The suspension springs were a bit more trouble since my washer doesn't have an access panel on the back however THANKS TO YOUR TIP to stretch the spring and put coins between the coils made this much easier . I don't know many guys that are strong enough to lay down and reach through the front and put those springs on the back.
Of coarse the belt was easy.
I also really like you list of probable solutions to the problems with the machine.
My wife is now happy with her washer again therefore I am also happy.
Thanks so much.
I can see me being be a loyal customer for many years to come.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Granite Falls, NC
- Parts Used:
- WP22004333
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
water valve leaking after wash cycle
Very simply put a screwdrive under the top and lift up off the clips and lay it back will expose the Water Inlet Valve,take the 2 screws off,pull the 2 water lines off,2 electrical wires and thats it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from SUNNYVALE, CA
- Parts Used:
- WP22004333
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
water was leaking while spin drying
top cover lifts up and folds back to expose the water solenoid switch. Disconnect water inlet hoses and wires and replace switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maloy from NORTH AUGUSTA, SC
- Parts Used:
- WP35-6780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Machine was shreiking during spin cycle. Terrible noise
Looked under the symptoms .I had replaced the belt 2 weeks ago, so I ordered the drain pump. Pulled washer away from wall, removed water lines, unplugged electric. I removed the rear panel, found the old part right there, disconnected the in/out tubes, removed old pump, installed the new, re-attached hoses, reinstalled the belt over the 3 pulleys, re-installed access panel. Reconnected water and electric after placing washer back in position. Runs like a new machine!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LEWIS from ROSWELL, GA
- Parts Used:
- WP22004333
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Water leaking into tub between used
Unplug electrical plug and shut off water supply. Putty knife to release latches at top left and right corners of flat top top where cloths go into washer. Take picture of wiring connections. Remove water diverter cover by unhooking snaps. Remove single screw holding water diverter. Remove single screw holding inlet valve and pull valve and water lines thru access hole. Disconnect wiring connectors and unscrew water supply lines. Reverse process to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from MADISON, TN
- Parts Used:
- WP35-6780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Loud noise in spinning cycle
There is a small back panel about 14" square made to open for access to the drain pump. 3 screws for the back panel and 3 screws for the pump - Oh you do have to slip the belt off & back on, underneath the machine.
Was this instruction helpful to you?
Thank you for voting!