BA8140 Maytag Washer - Instructions

open top of washer
remove two screws that hold water inlet valve
disconnect four wires and hose;replace new water inlet valve and reversed operation
everything went well

Did the same as others. Loosened the three screws diconnected the wires and put them on the new valve. Disconnected fill hose and connected to new valve. 10-15 minutes. Replaced panel and tested new part. perfect, My repair was a little longer, I vaccumed up all the dust bunnies I could find before moving washer back. Good for another 35 years, I hope. Thanks for the help and experiences.

Solved theprobel m by noticiing the HOT water filled the tub and it began to run when it was full. Figured out it was the solenoid valve. Ordered a new one. Simple to install and then it ran just fiine.

Washer is enclosed in a walled partition. I spent more time moving the washer out so I could get to the back of the machine. Due to Maytag's design of a removal sheet metal panel holding the valve the entire water valve replacement was performed outside of the machine. The replacement valve was an exact duplicate and made it a simple swap out. More time was spent removing inlet hoses and outlet hose then in actual valve replacement.

Diagnosed the problem and ordered the part online in about 15 minutes. Part arrived about 3 days later. I followed the directions that came with the part and VOILA! washing amchine fixed. I unplugged the washing machine. I unscrewed the the screws at the back of the machine. Pulled out the faulty part and disconnected the electrical wires. Connected the electrical wires to the new part, and screwed it back in. In less than 30 minutes, I was done.

First, I opened up the back of the machine to see the way the water got into the tub. I turned off the water at the pipes, unplugged the machine, and disconnected the hoses from back. There were no leaks with the hoses, so I looked at the part that managed the water flow when operating and went on line to find the part.
I found it and then ordered it from partselect.com. I got it two days later. I looked at how the other part was connected to the hoses and reused a clamp. I recommend getting a new hose clamp to make fitting it faster. I felt great after I got it to work, so that we didn't have to buy a new washer (the part was only $26). I think that Repair should be added to Reduce, Reuse, and Recycle.

Removed door panel to get to the electric control conponents and noticed a burned wire to one of the door microswitches. Ordered the door switch repair kit from PartSelect. Also, ordered and replaced the thermal fuse at the same time since it was only $12 and didn't know if that blew at the same time the switch cooked. I had the parts coming standard delivery (3-5 days), but they arrived the very next day. Parts included easy to follow directions.Job went pretty smooth and the dishwasher works again Good experience!

Shut off water supply, unplugged washer power, removed supply hoses from old washer valve assembly, removed valve mounting plate and removed old valve assembly from mounting plate, diagrammed and disconnected hot and cold solenoid valve wiring and removed valve assembly outlet hose. Installed and connected new valve, performing the preceding steps in reverse order. pressurized new valve, verified valve function and checked for leaks and placed washer back in service.

Removed the four screws that hold the part and also loosened the screw for a cover. Moved cover to gain access to inside of machine. Removed broken piece and replaced. Tightened screws and replaced plate. No leaks.

Loosened the hose coupling, removed the old washer and strainer; cleaned the opening; flushed the opening; installed new strainer and washer; reattached hose and "Bob's your uncle"! No problem.

Exactly as the video showed. This was a very simple repair. The only extra thing I did was to replace the mesh screen/gasket at the hose ends. They were plugged with crud. PartSelect saved me from buying a new washing machine. Yay!

I took the hot and cold water hoses off with pliers.and then I took the one screw out towards the top of the water inlet valve plate.disconnected 4 wires,there is a small clamp on the small hose on the valve you have to remove.and last there is a cluster of wires that has to be removed from a bracket and (it is important to put these cluster of wires back in place otherwise they will wear a bare spot in them.)

My experience with my repair is as follows:
After determining the "hot water" solenoid was weak and that a new fill valve was needed, I placed my order with PartSelect on Thursday and to my suprise, had it in my hand Friday evening (no special shipping). WOW talk about fast! But unfortunately the part was broken.
Called PartSelect back Saturday morn to explain my problem and was told that I would be credited for the broken part and that a replacement would be sent ASAP probably arriving on Wednesday. Again to my suprise, the part arrived on Tuesday morning.
Hats off to you guys for great service, prices and no hassles.

Dennis Fleming
North Billerica, MA

Removed three screws - Disconnected both inlet water hoses-Disconnected 4 electric clips-Removed internal hose connection from the same unit- Reverse order in assembly.

The repair was simple, and followed the instructions exactly. Removed three screws, one small hose clamp, and two electrical connectors. Replaced and reassembled. Worked like a champ!