BA8140 Maytag Washer - Instructions

Other guys have already spelled out in fine detail how to do the actual replacement. What I would add is this: First, I promised I wouldn’t swear during this repair. Second, I got everything I needed together including tools, a small bucket and some old newspaper to soak up the water that is sure to spill. I bought 6 foot stainless steel hoses to replace the old rubber ones. THIS IS HIGHLY RECOMMENDED as the last thing you need is a burst water line. Shorter hoses limit the distance you can move the washer without disconnecting them. The directions were wrong in that I did not need (nor could I use) the plastic sleeve over the outlet tube. So I very carefully had to pry this off without breaking the plastic bushing. And I had bent the clamp securing the outlet hose to the valve, and had a devil of a time getting it back on properly, so you may want to have a small tubing clamp handy as a replacement. Also, I checked for leaks before putting the valve back in place by holding it very carefully, powering up and turning the washer on and off a few times. Keep your fingers and sheet metal away from the terminals or your promise not to swear will be null and void! The last thing is that when I get into a project I go all the way, which meant pulling the washer all the way out and cleaning the floor and all the dust behind it, and even cleaning the washer itself. The result is my Maytag works like new, fills fast without the buzz and looks new, too. I love it when a plan comes together.

After reading partselect.com and a few other web sites, I thught the leak was either a hose clamp, hose, or syphon break.

1. Two screws at the bottom front are removed,
2. Bottom front moved away from the machine unitl the top clips allow it to come off.
3. Remove 2 hex head screws from the lid (look up, use a nut driver or I used a socket.
4. LIft the lid from the front (similar to lifting a car hood)
5. Syphon Break is in the top back right.
6. 4 screws in the back and a hose clamp that connects to the pump.
7. Put it all back together in reverse.

I had considered replacing the hoses while I was at it, but they all looked fine. Suggest you order the Syphone Break "Kit" because it contains clamp, and ring gasket that is between the break and the discharge elbow.

Works Great! Saved myself at least $150 in service call and parts markup.

Agitator motor burned out -- purchased new one through Parts Direct (parts still available) 4 bolts and plug and play wire harness and now runs like new.

It was really quite simple. I found out where the leak was coming from by taking off the front panel and running the washer through the drain cycle. PartSelect website was right on for what part I needed and delivered it promptly. The installation video from PartSelect couldn't have been more clear. I removed a few screws from the back of the washer and installed the new part in about 1 hour. All was good.

After disconnecting the power and removing the input hose connections I was able to remove the valve assembly through the back panel. I then removed the wires from the valve and disconnected the outlet hose. I removed the old valve and replaced it with the new one. Then reattached the outlet hose and 4 wires to the new valve. The assembly then was reinserted into to the back panel and screwed into place. Reconnect the input hoses and plug it in and it's ready to be tested for leaks & used. (I had no leaks, BTW. A little silicone grease on the fittings made reassembly go easier but it's not needed. )

Shut off the electricity (pulled thee plug). Working from the rear of the washer. Removed water hoses with Stillson wrench. Removed two self tapping screws with nut driver to get to the assembly. Slipped off the wires lugs one at a time from thee old assembly and slipped them onto the new valve assembly in the same location. Installed the new assembly. Attached the water hoses to the new inlet valves. Note: My washer had the hot and cold valves identified on the washer. The replacement valve assembly was marked hot and cold (H, C.). which was the reverse of the marking on the washing machine. Go by the marking on the washing machine.

Terrified that the washer water value would blow due to the noise... Diagnosed the problem, ordered the part and it took only 10 minutes to fix. The hardest part was moving the washer in the confined space, which required moving the driver out and sliding the washer at a 45° angle in order to reach the access panel. Once access gained it was straight forward. Step 1 removed fill hoses from supply. Backed the valve assembly out; detached water hose from value assembly with nut driver; detached wires'; value released; added new value and reverse process. Checked for leaks, reassembled fill hoses with new washers (stainless steel hose), ran cycle, checked for leaks, replaced washer in original position Need commend the video producer and repair person in the video. The narrative gave me the confidence that, Yes, I can do this.

I took the front off the machine and ran the cycle to see when it was leaking. I found it was leaking when it was draining the water out on the inside of the machine where it was going out of the machine. I took that part out off the drain hose and ordered the part no that was stamped on the part. The part came in and I reassembled everything and it did not leak.

un hook electric and shut off water:
had to remove top of washer
remove two screws holding valve in place
un hook water line and elec. wires from valve
reverse to put new valve on
Billy Myers
Alamogordo,NM 88310

Followed web instructions.

I removed the two screws that held the front panel in place. Then I removed the two screws that held the top down. This allowed me to see the siphon valve when I lifted the top up. I disconnected the hose from the pump to the siphon valve by taking off the 2 clamps. Then I went to the back of the washer and moved the drain hose from the back by looseneing the clamp. Then I unscrewed the 4 screws holding the siphon valve in from the back. I took off the old valve put the new valve in and reversed the process to reinstall. It fixed the problem.

Shut off the hot water supply (pretty sharp eh?). Disconnected the hose from the hw supply and the at the connection to the washing machine. These had not been touched in at least 15 years and were somewhat tough to loosen but finally came ..... accessibility was a problem for the connection to the water supply as it was in a recessed wall box. Fortunately, we had some washers for the hose connections so the install was a snap. Hardest part of the whole job was moving the washing machine out from between the drier and the wash tub .... tight fit. Thanks for the quick service and to FED EX for their delivery. The delivery fellow was a real gentleman.

1. Removed hoses 2. Removed inlet valve. 3. Took valve apart to discover defect in diaphram. 4. Looked up and ordered part. 5. Replaced inlet valve. 6. Tested washer.

I followed steps outlined on you web page.

since i had already opened up the machine to remove the old part, all i had to do was install the new part. actual time was less than 5 minutes. additional time was in putting the machine back together.a more detailed description would be:
i inserted the part in the sleeve at the back of the machine,held it in place and replaced the four screws to hold it. i attached the hose and clamped it. i then re-fastened the machine's top with two screws and replaced the front panel, using the two screws to hold it in place. the machine was used the next day and worked fine.

After getting my husband and another strong guy to move the washer from the wall... I removed the single screw that held the access in panel below the elbow. I then removed the 4 screws that held elbow pinned between the syphon break and the rear panel of the washer. I reached up and removed the broken piece of elbow and replaced with my new syphon elbow. Within 20 minutes I had the 5 screws replaced and the access panel cover back on and the washer moved back into place against the wall. Since we broke the elbow moving it around during home remodeling... I was able to complete our first load of wash in 6 months that afternoon! Thank you!