BA5000 Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Greg from Bethel Park, PA
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Water would not shut-off at initial filling of tub, hence washing cycle would not start. (This condition could have gone on for days as the water exited the wash machine as fast as it entered.)
Removed the front of the washing machine. Located & removed the water inlet valve from it's mounting on the back
inside face of machine. Replaced water valve, & restarted machine. Like new again!
Can't say enough about the speed of parts delivery & professionalism and accuracy recieved from the team at Parts Select. Thanx again,
Greg W.
inside face of machine. Replaced water valve, & restarted machine. Like new again!
Can't say enough about the speed of parts delivery & professionalism and accuracy recieved from the team at Parts Select. Thanx again,
Greg W.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from Corpus Christi, TX
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
slowly filled with water
The hot water side would fill quickly but the cold water filled very slowly. The seloniods and the valve is built all into one unit. I ordered and replace the part in no time at all. Now both hot and cold water fill quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Marion, IL
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
very little hot water incoming
Took out 2 5/16" screws and loosened top and took off two ground wires and 2 hot wires for cold & hot water solenoids and removed & replaced solenoid wires and fill hose. Also Had fantastic delivery of parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Dixfield, ME
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Hose hookup was cracked.
My husband did this repair. He disconnected the old part, laying them out in the order that he took them off. He put in the new part and hooked up the hoses and we had a working washer again. I ordered the part and a couple of days later it arrived on our door step. Thank you for your speedy delivery. We live in a parsonage and the washer & dryer that were in here stopped working, so we brought our Maytags (used) from our camp where the problem occurred because of winter freezing. Thanks to Maytag for making this repair so easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luther from Valrico, FL
- Parts Used:
- 206638
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Machine was leaking water on floor.
I found that the water was coming from top of syphon break. Took it out located it on computor , ordered part. Took about 10 min to replace. EASY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Paducah, KY
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Old water valve assembly cold water solenoid valve was leaking thru.
Shut off water supply, unplugged washer power, removed supply hoses from old washer valve assembly, removed valve mounting plate and removed old valve assembly from mounting plate, diagrammed and disconnected hot and cold solenoid valve wiring and removed valve assembly outlet hose. Installed and connected new valve, performing the preceding steps in reverse order. pressurized new valve, verified valve function and checked for leaks and placed washer back in service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Edina, MN
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
washing machine would not operate on cold water setting
Diagnosed the problem and ordered the part online in about 15 minutes. Part arrived about 3 days later. I followed the directions that came with the part and VOILA! washing amchine fixed. I unplugged the washing machine. I unscrewed the the screws at the back of the machine. Pulled out the faulty part and disconnected the electrical wires. Connected the electrical wires to the new part, and screwed it back in. In less than 30 minutes, I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carrie from Ann Arbor, MI
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The part that control water into tank was dripping
First, I opened up the back of the machine to see the way the water got into the tub. I turned off the water at the pipes, unplugged the machine, and disconnected the hoses from back. There were no leaks with the hoses, so I looked at the part that managed the water flow when operating and went on line to find the part.
I found it and then ordered it from partselect.com. I got it two days later. I looked at how the other part was connected to the hoses and reused a clamp. I recommend getting a new hose clamp to make fitting it faster. I felt great after I got it to work, so that we didn't have to buy a new washer (the part was only $26). I think that Repair should be added to Reduce, Reuse, and Recycle.
I found it and then ordered it from partselect.com. I got it two days later. I looked at how the other part was connected to the hoses and reused a clamp. I recommend getting a new hose clamp to make fitting it faster. I felt great after I got it to work, so that we didn't have to buy a new washer (the part was only $26). I think that Repair should be added to Reduce, Reuse, and Recycle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Colmesneil, TX
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
water continued to trikle in machine
took hose off then took three 5/16 screws then clamp off reversed order to put back on check for leaks ok
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Belton, TX
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Water flow from the hot side was very slow.
I ordered the water valve at 12:42 PM one day and received the part at 10:25 AM the next morning. Now this is what I call excelent service. The price of the part was very reasonable. Getting my wife off my back for her washer being broken PRICELESS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Seneca, IL
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Inlet valve cracked and leaking
The repair was simple, and followed the instructions exactly. Removed three screws, one small hose clamp, and two electrical connectors. Replaced and reassembled. Worked like a champ!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JEFF from FORT HILL, PA
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
water coming in the wash tub when not in use
I took the hot and cold water hoses off with pliers.and then I took the one screw out towards the top of the water inlet valve plate.disconnected 4 wires,there is a small clamp on the small hose on the valve you have to remove.and last there is a cluster of wires that has to be removed from a bracket and (it is important to put these cluster of wires back in place otherwise they will wear a bare spot in them.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Hilmar, CA
- Parts Used:
- 208847
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Broken Syphon Fitting in back of the washer. Piece broke off when the washer was pulled out of position to clean out water screens.
Removed the four screws that hold the part and also loosened the screw for a cover. Moved cover to gain access to inside of machine. Removed broken piece and replaced. Tightened screws and replaced plate. No leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ken from lakeville, MN
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
cold water selinoid didn't open
Removed three screws - Disconnected both inlet water hoses-Disconnected 4 electric clips-Removed internal hose connection from the same unit- Reverse order in assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Jupiter, FL
- Parts Used:
- 12001413
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Deteriorated and clogged strainer; slow water fill.
Loosened the hose coupling, removed the old washer and strainer; cleaned the opening; flushed the opening; installed new strainer and washer; reattached hose and "Bob's your uncle"! No problem.
Was this instruction helpful to you?
Thank you for voting!