BA5000 Maytag Washer - Instructions

Part shipping was great got here in two days-

I pulled off Front panel (two screws) and lifted Top panel (2 screws) and disconnected the inlet hoses. I removed the old Inlet valve. (1 scew and valve to tub hose connection).

Before Installing the new valve, i shifted the connector positions on the selenoids to match the old valve. and installed by reversing the steps. All went very smooth. Thanks, It was easy.

When the part came in, it was just a matter of getting the old part out, and replacing it! Incredibly smooth---the hold down screws were obvious, so once I got them out---the part came out of the machine, I disconnected the two control wires, reconnected them to the new part---and reinstalled!

1. Removed hoses 2. Removed inlet valve. 3. Took valve apart to discover defect in diaphram. 4. Looked up and ordered part. 5. Replaced inlet valve. 6. Tested washer.

I followed steps outlined on you web page.

Followed web instructions.

After getting my husband and another strong guy to move the washer from the wall... I removed the single screw that held the access in panel below the elbow. I then removed the 4 screws that held elbow pinned between the syphon break and the rear panel of the washer. I reached up and removed the broken piece of elbow and replaced with my new syphon elbow. Within 20 minutes I had the 5 screws replaced and the access panel cover back on and the washer moved back into place against the wall. Since we broke the elbow moving it around during home remodeling... I was able to complete our first load of wash in 6 months that afternoon! Thank you!

since i had already opened up the machine to remove the old part, all i had to do was install the new part. actual time was less than 5 minutes. additional time was in putting the machine back together.a more detailed description would be:
i inserted the part in the sleeve at the back of the machine,held it in place and replaced the four screws to hold it. i attached the hose and clamped it. i then re-fastened the machine's top with two screws and replaced the front panel, using the two screws to hold it in place. the machine was used the next day and worked fine.

I first shut off the cold and hot water hoses so that no water would run while replacing the part. After that I made sure to unplug the washer .Then I removed the plate that was holding the water inlet valve with a 1/2 " nut driver ,I think there were four bolts .Then I removed two more bolts from the center of the plate that were holding the water inlet valve.I then disconnected one 1/4 " screw or I should say loosened one which held the main water hose going into the washer which then released the part ,except from four wires. I then took one wire off at a time and attached to the new part one at a time.Finally, I was finished and reconnected everything .It worked perfected !I'am very happy and pleased . This washer is over 25 years old and still runs .

I removed 2 screws at the bottom front corner of the washer. Then lifted the front panel upwards about 45 degrees, which allows the front panel to be removed.
I then removed one small lag bolt from under each front corner (with a nut driver), which hold the top to the frame.
I was now able to swing the top up to have access to the siphon break.
I then removed the drain hose from the rear of the machine where it is attached to the nipple end of the siphon break, by loosening the hose clamp. Still at the rear, the nipple end of the siphon break is attached with 4 mini lag bolts, Which go through the back plate & hold the siphon break to the inside of the washer. I removed the bolts with a nut driver.
The nipple end now fell away. You must save it, as the siphon break does not come with a new nipple end.from the siphon break. Maytag attaches it with an iron band, as they must think that this repair will never be done! I cut the band with the Dremel, being very careful not to cut the hose.
I pulled the siphon break free from the hose.
The installation is a reversal of the removal, starting with inserting the siphon break in the inner hose, clamping the hose with the supplied hose clamp.
I the removed the inner drain hose

Removed old valve and replaced with new. Wire for wire..screw for screw..

Removed the screws with a small socket set. Moved around cover over so I can remove broken syphon. Placed new Syphon in it's place. Attached the hose to Syphon with new clamp and wala! Machine is back to normal. Thanks Parts Select :)
P.S. Delivery was faster then expected.

I checked the inlet hoses for hard water build up and noted that this was not a problem. Then checked the hose from the inlet valve to the washer drum and determined that it was clear so I knew the problem was a faulty inlet valve. After receiving my replacement valve, I removed the old valve by removing the hot and cold water hoses and unscrewing two screws securing the inlet valve and lifting the inlet valve out the metal holding bracket. This gave me complete access to the inlet valve allowing me to remove the hose clamp and hose to the washing machine drum. The new inlet valve was an exact match so I removed the four electrical wires one by one while putting them back on the new inlet valve to insure correct electrical connections. I added a piece of one half inch plastic tubing provided with the new inlet valve on the outlet nipple of the new inlet valve to prevent leaking. I then put the new inlet valve back into the holding bracket and screwed it down. I replaced the hot and cold hoses to the new inlet valve carefully so as not to cross thread the plastic connection on the new inlet valve. After turning the water back on, I checked for leaks and plugged the washing machine back on to test it with a washing cycle.

Followed instructions, those were OK.
Dishwasher front still leaking

Disconnected the hot/cold water hoses. Removed screw that holds water valve in place. Removed two screws that hold valve to metal plate. Disconnected wire terminals from old valve and installed on new valve on the same spades. Disconnected water discharge line by loosing screw that hold line on valve, reattach to new valve. Removed old valve from plate, installed new one with the two screws to plate, then put in place and put in screw that hold valve in back of washer. Connected hot/cold hoses and fired it up and noisy water eliminated. About 30 minutes and back in service which made the wife happy that her washer was quite again. Thanks!

1. Identify washer model and symptom
2. review page of suggested part; view installation video
3. order part with standard shipping
4. receive part next day and install just as the video showed

Entire job from going to PartSelect website to completion took less than 24 hours. Hardest part was moving the washing machine. Machine is nineteen years old and now works perfectly. Unmatched service.

I had taken the washer out and replaced both hoses, and the leak stopped for a load or two. I then replaced the water inlet valve, because I could see that the plastic threads were pretty bad. The repair is very simple on this model. There is no need to open the cabinet at all, the entire job is done on the back. I used a socket and the stubby driver for the mounting screws and switched to a screwdriver tip and opened the clamp on the hose leading to the air gap assembly. The entire operation took about five minutes. The repair worked for two or three loads.

The water leak came back, so after some searching I finally figured out how to open the cabinet, and that took longer than actually doing it. The front opens with two big screws located on the front about 4" above the floor, just in the corner of the indentation on the panel.

With the top tipped up (tape the lid!) out of the way, the leak proved to be coming out of the air gap assembly. There is an injector nozzle and a rubber sleeve that goes over it. They fit in the large black hose. I easily opened the hose clamp, removed the old parts, put in the new one. The rubber sleeve has a cover that goes over the edge of the plastic injection nozzle. You have to make sure it is entirely and smoothly inserted. Easy. Then insert it all the way to the shoulder of the end of the hose with that wide end facing into the hose and the other end open. Slip the open end through the bracket and into the other hose. Tighten all your clamps, and carefully pressure test. Do not touch any metal parts if there is water spewing. Just turn it off, pull the plug, and fix the problem. In my case, it worked perfectly, and I turned it off, replaced the front and the job was done.

Despite the great advice I got here, I ended up getting the nozzle parts in town. I had to go to an appliance parts outlet rather than a place like Home Depot, but it was quick and no shipping. Still, I would not have tried this without the great advice and fast service here.