MAV6000AWQ Maytag Washer - Instructions

Parts needed: Snubber Ring and 6 Springs (don't put the old springs back)
Unlug the AC cord, open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back It was not necessary to remove the back cover. Remove the little hose going to the basket from the control module. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING: DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK. Seriously! Install the new ring, center and tighten the screws. Put the tub back in. I found it handy to support the tub with a 2x3 to get the springs back in. Connect hoses back up. It really isn’t that bad, a couple of scraped knuckles.

I followed the direction came with the part.

• I unplugged power electric wire from the wall.
• Unscrewed total of five screws from the back of the top console.
• Removed the top console to gain access the switch.
• I took pictures of the switch position for a future reference.
• Unplugged the switch wire by just pulling the plug.
• Carefully removed the switch and pulled the plunger out plunger assembly.
• Entered a new plunger in first and inserted a new switched carefully.
• Opened and close the lid few times to check the switch is going on an off properly. You will hear clicking sounds.
• Plugged the switch wire to the new switch.
• Reinstalled the console and screwed back the five screws.
• Plugged back the electric plug in wall outlet.
• Tested the washer by washing a full load of clothes.

The whole process took me about 30 minutes.

-Abhay

As for how I did the repair , I just followed your instruction video . The instruction video provided by Part Select was very very valuable.
The snubber ring was a piece of cake BUT would have been really difficult without the helpful hints in the video like replacing three of the screws in the rings collar with three longer screws so as not to disturb the spring under it.
The suspension springs were a bit more trouble since my washer doesn't have an access panel on the back however THANKS TO YOUR TIP to stretch the spring and put coins between the coils made this much easier . I don't know many guys that are strong enough to lay down and reach through the front and put those springs on the back.
Of coarse the belt was easy.

I also really like you list of probable solutions to the problems with the machine.

My wife is now happy with her washer again therefore I am also happy.

Thanks so much.
I can see me being be a loyal customer for many years to come.

Took off the upper back that had 6 screws with a screw driver. Found the lid switch . Removed it after I figured out how to remove it. It was a little tricky without instructions. Putting in the new switch was a little tricky also. You have to angle the front of the switch in, pop it in and then push it back so it can snap in. Once I put it in, the washer started right up. I was very happy. Instructions would have been very helpful. I am very pleased with this company because I received my switch in a couple of days. I will definitely use this company again.

Took the back plate off, popped the old lid switch out and the new one in. Very easy. No problems, saved $100 buck at least doing it myself.

very easy replacement. was probably broken for a year and only took five minutes to replace. Can't believe we waited so long!

After just over ten years of use (purchased in early 2001), my Maytag Atlantis started making an awful noise during the spin cycle. The noise was very loud and sounded like metal grating on metal. Looking through posts on partselect.com, I identified the problem as the drain pump and pulley. Looking under the washer I could see that where the pulley connected to the drain pump the metal was starting to fall apart. I ordered the drain pump with pulley and a washer belt. The belt didn't look overly worn, but I figured now was a good time to replace it. The parts arrived within a couple days, faster than I expected. I opened the top of the washer by inserting a putty knife about an inch in on each side to release the top which then easily clam-shells back. I removed the front panel by removing two screws in each corner. Using a few blocks of wood, I propped the washer up in the front so I could remove the drive belt. The motor is spring-loaded and is easily moved to allow for belt removal. Then I removed the two tubes that connect to the drain pump. The drain pump was quickly removed from the washer; only three nuts hold it in place. The new pump/pulley went back into place using the same three nuts. After reconnected the two tubes to the pump, I installed the new drive belt. I put the front panel back on, and seated the top back in place. Anxiously I watched and listened as the washer cycled through a load. To my relief, the problem was fixed. All told, it probably took about 15 minutes to make the repair, and with any luck I’ll get another ten years out of this washer.

Followed directions from video on your site. It was very helpful. The snubber ring fixed the problem.

Removed front and rear panels, removed belt, removed old springs, disconnected bleach and pump lines from tub and lifted entire tub/transmission assmebly from washer. Replaced snubber ring at bottom of transmission assembly by backing off screws just enough to allow old ring to be removed and new one to be installed. Replaced pump assembly by removing drain hose and three bolts. Installed in reverse order. Placed tub/trans assembly back into washer and installed new springs using vise grip pliers. Reconnected bleach line and pump lines to tub. Reinstalled fron and rear panels. Installed new belt on bottom side of washer. Piece of cake.

1 I opened the top of the washer found the top plastic rim piece broken due to the fact that it cracked while unbalanced one time. Which made it leak which ate away the rubber seal . The parts were here fast and they were the right ones. Great job and I will tell everyone about you thank you verry much.

figured out how to open the top of the washer(Two small tabs I pushed in with a putty knife. Looked for the area it was leaking. Slide the hose clamps off with a pliers and pull out hose.

Put clamps on new hose, replace hose and slide clamps to ends to seal the connections

The key is knowing what to open to get to the valve. The top of the washing machine lifts up once you push back the spring clips in the front. After that, it was easy to remove the old valve and replace it with the new one. The instruction sheet provided also helped.

disconected water lines unplug power and took drain pipe off, used putty knife to open top of washer and pulled off front removed pannel off back pannel, disconnected water level tube,using vise grips took off springs and pulled tb out used 5/16 socket to loosen screws just enough to pull snubber ring out replaced with new one reversed prosses in putting it back to geather

First i unscrewed the bottom latch to check inside the maching, i then disconected the vertical style pump with pulley from its position and i discoverd a huge crack that was made by a loose pulley. After that i ordered another pulley from this web site easaly installed the pulley and now my maching works like new. The part was less than 50 bucks i saved over 200 bucks by not going out and buying a new machine.

pop top,remove 2 screws,remove front panel.remove 2 spring clamps from tub hose.reverse!