MAV6000AWQ Maytag Washer - Instructions

I removed the screws to loosen the belt, took off the old belt and put on the new belt. Tightened it up and has been working ever since.

Thank you, Lester

you guys ship faster than anyone else. One day I order the part and a day or two later there it is. :)

Replace the motor in 25 minutes, my repair guy said it was not worth the time , I got this motor for less than $150. And save my self over $600.00, this was incredible.

iremove the two screws that is on the lid and then ipulled that out then secound step remove the part is on the back were is the suit of the washer machine were is the hoses of the water hot and cold its berry easy to do it your self thank you

The Repair went well . I had the hose on in about 30 seconds . The best part about this ordeal was the ease of finding the part on your website , and the speed of the delivery . I had my part in about 2 days , put it on and back to the fun part of clothes washing . I would recomend this company to everyone. Thanks, Rick K.

I went ot the Parts Select web site, and read what other people had done with the same problem. The advice was right on. Using the paper towel to hold the screw in place during reassembly ws great advice. Thanks for the heads- up.

Use a blade to pop off the fabric softener dispenser cup. Use socket and extension to unscrew the single hex bolt that attaches the assembly to the shaft. Lift off the assembly and recover the flat washer. Install the new assembly over the shaft and install the original hex bolt and washer. Tighten firmly. Snap the dispenser cup back in place.

take a butter knife and pop the clips loose on the front between the lid and the front take the two screws loose on the front in each corner remove the front cover and you will see the hose take the clamps off and replace the hose

unpluged the machine , turned off the water .
removed as much water i could by hand ,with pan & towels .
Removed the front panel , tip machine on back feet & prop up .
removed belt from under the machine , take the drain hose off pump , remove pump .
installed new pump , rehook hoses , install new belt & motor pivot spring .
put front back on lower machine turn water back o
n , and plug back in .

I knew it was the belt because of all the noise it was making. I ordered the belt and it arrived real fast. I pulled the washer away from the wall and tipped it back at about a 45 degree angle against the wall so I could get under it. I propped it with a bucket. I then pulled the old belt off and spun the new one on. Real fast & easy.

Took a putty knife and raised the top,then took two bolts out, then pulled front panel off. Took hose off from the tub to the pump,and put the new one on. It's working fine.

I popped off the fabric softener on top of the agitator. Used an extended arm on my socket set to remove the only nut holding the agitator on the motor assembly apparatus. The agitator came off with ease. Just reversed the procedure in replacing the new agitator. This was an easy job.

removed control pannel, traced current flow to lid switch,in but not through, shorted power in to motor lead machine started, ordered switch, received switch, installed new switch, washed clothes.

I'm not a washing machine technician but I did nurse a new Kenmore machine for 23 years and was ready for a replacement. Craigslist advertised a Maytag I was interested in and I bought it with the seller's assurance that it worked perfectly. It didn't and I went online to try and figure out what might be wrong. Clearly, the tub was traveling beyond it's design limit and I suspected a spring or two might be involved. Somewhere online, I found the illustrated parts diagram and then went looking for additional information. To my extreem delight, I came across a do it yourself repair video that demonstrated the procedure well enough that I was completely confident I could make the repair with little effort. That video was one of several service related appliance videos offered for free throughhttp://www.do-it-yourself-washing-machine-and-dryer-repair-help.com/index.html/ The final consideration was whether I could buy the replacement suspension springs and snubber ring for less than I paid for the washer. I found PartSelect and within minutes, I had the parts ordered. The parts arrived within 4 or 5 days, as promised, well packaged and in perfect shape. This morning, using the video as a final reference and the new parts, I completed the repair with only a minor hitch. Without the special spring tool used in the video, I struggled a bit with getting the new springs attached. That's where my wife came in handy (after all, she was movitated). Having her tilt the drum toward the spring landing made it much easier for me to stretch it into place using an adjustable locking plier. I actually enjoyed the whole procedure.

Removed entire cabinet from base, removed drive belt, removed suspension springs, removed tub and transmission together.
Removed 6 screws from brake housing to access snubber. Didn't have the special tool to compress the spring for reassembly, but used 3 longer screws to pull the brake housing back down...worked fine. Reinstalled transmission / tub and replaced all 6 springs. Reassembled cabinet. Unit spins great now...like new.

Removed front panel also right side panel to get to the springs. Used vise grips to extend springs and used coins to keep springs open for replacing.