CAV1004AWW Magic Chef Washer - Instructions

unscrewed screw holding old actuater in and replaced it whith the new part.

I checked the belt 1st. It didn't look like it could be the problem, but it needs replacement anyway. Replacing belt is very easy, this 1 is at the bottom of the washer.

1. Unplug washer.
2. Move it away from the wall.
3. Tilt washer back & support the bottom front with lumber.
4. You can see the belt looped around 3 pulleys. Water pump in the back. The motor is in the right front & is spring loaded.
5. Grab the motor pulley & push it back as far as it will go, & remove the belt from it.
6. Do the reverse to install new belt.

There is a Brake Rotor & Lining Assy on this washer. I looked up the part on this web site, sure enough somebody else had this same problem. Part is on order. If this is not the fix, I will revise this posting later.

First I lifted the top of the washer to get access to the screws that held the hinges in place, unscrewed them, removed the broken hinges and put the new ones on, replaced the screws and closed the top. It was very easy. I was amazed that I could still get replacement parts and at such a great price, less than $15.00 with shipping!

The hardest part was finding the model # on the back. I couldn't move the washer out...so used a mirror! I used a putty knife to pop the 2 fasteners securing the top. Tilted it up & proped with a plastic clothes hanger. Unscrewed the one screw which is easy to get to with the top up. Replaced the hinge with the 1 screw. Closed the top. Gave the broken hinge to my wife as an early Mother's Day present.

Remove back compartment, remove belt disconnect two water rubber tubes from the drain pump, unscrew three screws securing the drain pump from the frame. Replace with a new drain pump, secure to frame with thee screws, reconnect rubber tubes, and replace belt.

Top loader May Tag washer with open bottom. After research I presumed it needed a new belt, or Transmission, which runs 3 pulleys under the open bottom. After tipping the washer back for inspection, saw oil splatter underneath. Removed old belt by turning largest pulley on Transmission while pulling the belt "off" the edge. Belt was aged, Stretched and worn. Belt and all 3 pulleys were oily causing slippage. The main large Drive pulley on the Transmission shaft, has a plastic snap on grease cup at it's center. I snapped it off with screw driver. The cup was partially full of thinned old grease causing the oily mess. There's a C clip inserted in a groove on the end of the drive shaft holding the pulley on. Removed the C clip with screw driver tip and slid off the Drive pulley. The Center of the pulley contains a plastic ratchet assembly that operates the washer tub cycle to rotate and stop and repeat. The ratchet assembly falls right out, and in the end of transmission is a Thrust washer which can be pulled of easily also. I Cleaned all 3 pulleys with De-greaser and finally with Rubbing Alcohol to dry the pulley surfaces. Then cleaned and removed all grease from the plastic ratchet assembly parts and cleaned them. Then I Repacked everything including the Drive shaft with "heavier" Grease that would not break down so easy. Reassembled everything in reverse and installed on the shaft. Snapped the C clip back on to hold pulley back in place and then the Grease cup, which just snaps back in place with a push. Installed new drive belt in the same manner it was removed, only in reverse by turning the pulley, and pushing the belt "on" over the edge of the pulley. Problem fixed and washer works perfect again with Noticeably better operation through all washer cycles.

Hving read some of the tips in regards to this repair I set out with equal parts of confidence & apprehension. The advice of shifting the tub toward the hinge to be removed is in itself the key to the whole procedure. After having done so & wedging a dust pan handle between the tub & frame to first one side & then the other, I removed the entire lid with the hinge & hinge pin assys. attached as ther is not sufficient clearance to slide a servicable hinge pin from a hinge when only one hinge has beeen removed. With the lid completely removed access to the hinge pin(s) is straight forward. I suggest screwing & unscrewing the fastening screw into a new hinge assy before mounting the hinge onto the machine & also using an offset philips screwdriver or ,as I did, a 1/4" drv. ratchet with a #2 philips apex bit which allows for a better feel & more control over the upside down blind operation of removing & replacing the fastening screw into the hinge assy. Hope this helps. Tom

Pretty simple repair--popped the fabric softener cup off of the agitator top and took out the bolt that secures it to the assembly. Removed the broken agitator top, replaced with the new one and reinstalled the bolt and softener cup. EZ as pie for only $24 including shipping! Great price!

Fabulous turnaround time from www.partselect.com. I had the problem corrected inside of 4 days using standard shipping. I will definitely do business with them again!

Removed the screws on the back plate pulled the hose clamps off removed the belt and three screws off the pump went back just as easy and the machine was like new again. If only all repairs was this easy!

Turned off the water supply. Removed clothing and bailed out water fro tub. Removed back access panel. Turned washer over to access the bottom and removed drive belt by turning the large pulley attached the drum while pulling the belt over the pulley. Next remove the two hoses attached to the pump, remove the screws holding the pump on and remove the pump. Replace the pump by reversing the procedure, as for replacing the drive belt, place the belt on the motor and pump first and start it on the larger pulley and hold it on while you turn the pulley, it will pull the motor adjustment as you turn and when fully in the pulley it will be properly adjusted. Then replace the access panel, turn the washer upright, push back in place, turn on the water supply and replace the drain hose. Back in business. For me, while I was waiting for the new pump to arrive, I took the time to remove the agitator and tub and give it a good cleaning inside and out, but that's me.

I pretty much followed the video,and read some of the other comments on how to do it. I only had one problem, the back panel had an opening of about 14"x14" to access the 2 rear balance springs. I finally laid the machine on it's face,so I didn't have to kneel down.The only problem with that,is the tub falls forward, making the springs farther away from the upper hole to attach/stretch, the springs to remove/install. I cured that problem by cutting a wedge out of a piece of 2x4, and stuck it between the top edge of the tub & upper frame. Worked great,held the tub in position, closer to the springs & locating holes. Taking them off is no problem,installing them, was made easier by using the wedge. The parts were a perfect fit, no more 'walking away from the wall' now! Thanks PartSelect

Took the whole machine apart tipped tub upside down to put on snubber ring. One person had to hold down very very firmly to the metal ring that fits on top of the snubber ring while another person quickly screwed in the screws to hold it down.
The springs required an extra strong person and a few words of frustration to stretch to get them on. My son who is 39 years old did it. My 60 year old husband would not have had the strength to stretch the springs.
So far it works great. My son washed his carheart jumpsuit and coat with not a sound or wiggle. Your trouble shooting site was what made us decide to order what we did because of the percentages of what the problem was beside each part. Thank you for being so prompt in sending our parts.They came so quickly we weren't without a washer but maybe a day or two.

Pop the top of the washer and use the nutdriver to remove the two screws holding the frontpanel on. Use the nutdriver for two more screws holding the plastic motor cover on. Use nutdriver for the two BIG screws holding the motorplate to the washer frame. After this, I literally beat/chiped/sawed the old motor geat off. Once that was done, I put the new one on; had to use a hammer to knock it all the way on (try not to damage the clips). Reassemble everything. Flip washer over and place bet around two smaller gears. Rotate main tub gear to feed belt on. Make sure you use the nutdriver to loosen/tighten the motor positioner screws in the slots if things aren't working here.
The only really hard thing was taking the old motor gear off.

Removed the inner basket and outer tub to replace the gasket and rubber seal. just had to remove about a dozen screws to get it out.

Tipped the machine up to replace the belt.
The noise didn't go away at first. I decided to spray all the pulleys with some silicone spray, that did the trick.

Took off the back plate. Looked to see where it was leaking. Squeezed the clamps on top and bottom to remove from hose and pull hose out.