CAV2000AKW Magic Chef Washer - Instructions

Removed entire cabinet from base, removed drive belt, removed suspension springs, removed tub and transmission together.
Removed 6 screws from brake housing to access snubber. Didn't have the special tool to compress the spring for reassembly, but used 3 longer screws to pull the brake housing back down...worked fine. Reinstalled transmission / tub and replaced all 6 springs. Reassembled cabinet. Unit spins great now...like new.

Leaned washer forward, removed clamp and old hose, replaced with new hose, reinstalling clamp.

Popped off bleach cap on top then got socket and long extension removed bolt, cleaned a little then replaced new agitater top.Replaced bleach cap and i was done.

Pulled up the top of the washer and removed the lid hinge with a star tip screw driver. Realized that I also needed the hinge pins and had to reorder those. They should come as a kit.

Hired someone. Note: I purchased two (2) hoses and (2) clamps -- this is the third time I am replacing a cracked hose. The manufacturer needs to use better quality and more flexible material for hoses.

We followed the instructions show on the video. However, our model was assembled slightly different. We had to remove the screws from both sides of the side panels so that we could remove the tub from inside of the machine. Also our model only has one belt not two.
Over all it was easy considering my husband and I had never attempted to repair a washer. Once we got it back together it when back to working like it had never been broken!
We would have never been able to repair our washer without the video that your site provided... thanks so much!!??

Sure wish the manufactures would consider making the older models again as lots of us are not happy with the new modules being manufactured presently!

Looked under the symptoms .I had replaced the belt 2 weeks ago, so I ordered the drain pump. Pulled washer away from wall, removed water lines, unplugged electric. I removed the rear panel, found the old part right there, disconnected the in/out tubes, removed old pump, installed the new, re-attached hoses, reinstalled the belt over the 3 pulleys, re-installed access panel. Reconnected water and electric after placing washer back in position. Runs like a new machine!

Hardest part was finding part that needed the needed repair. Searching the web for issues associated with the sound resulted in many links. Once the sound was found, I went to the video to see how to remove the Water Pump so I could examine it to confirm that was the correct piece. It took about 15 minutes to remove the part. Since I had to remove the belt to get it out, I realize that the belt needed replacement as well. So both parts were ordered. Replacing the parts also took about 15 minutes. Relatively easy repair. Be aware that the video on the part select video shows the water pump in a different location than the Maytag washer. To get to the Maytaq water pump, there is a panel in the back that had to be opened to access the water pump.

Removed the old hoses and screwed on the new hoses.

First, I disconnected the power cord then I removed the panel that held the knobs in place. Then I pulled the center holding clip, what holds the knob secure, with the screwdriver and the broken knob slipped right off. Then I put the new knob on the shaft and slid the holding clip on the backside of the panel. Lastly, I put the panel back and screwed it back down and that's all. Works like nothing ever happened.

I obtained the parts on line and began to install these. I was surprised that the ease of my installation was great. Each part was held by one screw. I used a phillips driver and found the under screws easy to get to by pushing the inside clothes drum to the side. A total of four screws was required for the replacement. This repair was so easy that a normal non-trained person can accomplish it. Thanks Admiral.

Parts needed: Snubber Ring and 6 Springs (don't put the old springs back)
Unlug the AC cord, open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back It was not necessary to remove the back cover. Remove the little hose going to the basket from the control module. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING: DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK. Seriously! Install the new ring, center and tighten the screws. Put the tub back in. I found it handy to support the tub with a 2x3 to get the springs back in. Connect hoses back up. It really isn’t that bad, a couple of scraped knuckles.

There is a small back panel about 14" square made to open for access to the drain pump. 3 screws for the back panel and 3 screws for the pump - Oh you do have to slip the belt off & back on, underneath the machine.

Removed front panel also right side panel to get to the springs. Used vise grips to extend springs and used coins to keep springs open for replacing.

I'm a 69 year old female. My husband isn't very handy so I decided to order the parts and do it myself. I didn't know how to take the machine apart so I just moved the washer part so I could unscrew the screw. I dropped the screwdriver between the adj. and side of the washer. I guess you won't be telling this story. I did get the parts on and the lid is working and so is the machine. Valerie Guyot