CAV2000AKW Magic Chef Washer - Instructions

tip washer up on wooden blocks.remove drive belt.remove "E" clip from tub drive pulley and remove all the parts.Install new parts in kit as per instructions.machine works great!

After pulling the machine away from the wall and turning off the water and unpluging. I simply removed the panel in the back and reached underneath and removed the belt. Took off the hose clamps and removed the three screws holding the pump on. Put the new pump back in place and hooked up the hoses. Then put the belt on for a test run.......all OK put the back on and was done. Whole job about twenty minutes. Saved over two hundred dollars doing this myself. Very simple repair.

Read DIY review from William, Middleton, OH on 01-15-08. Tip on how to relieve spring pressure on brake assembly worked like a dream (3ea 10-24X2 bolts/machine screws). Replaced brake and machine works like new and was an inexpensive fix. Once the shell/housing is off the machine, tub can be turned upside down and the base doesn't need to be removed. White powder under machine was a plastic wear ring that tells you when your brake rotor needs to be changed. Brake rotor still had lining but was much thinner than replacement part. Note* Use putty knife to push in clips on front to release the top lid section.

I was able to get the belt off easily but the belt was fine. I changed the snubber easily also. But that wasn't the problem. I went through all the parts that are easy enough to change without a mechanic but turned out it was something inside the innerbasket and we had to junk the washer and it was only 4 yrs old.

Removed the waterlines. Set the ends in a small pan or bucket to catch the water.Do the same with the drain line.
Keep an old towell handy as water will drain out of the drain pump when you remove the drain hose. Removed the back panel. Use a flat bladed screw driver to pop the top off the two clips in front holding the top down. Lift the top and pull the two screws which holds the front in place. Remove the front and set aside. Underneath, use gloves and the screw driver to remove the six springs by placing the screwdriver through the top hook end about an inch and with both hands lift the spring off. Carefull not to let the blade slip off and bust your knuckles on something,hence the gloves. Lean the machine over and walk the belt off the pulley. Disconnect the small tube in the back left corner from the drum and lift the unit out from the top. Set the drum on it's top and loosen the six screws under the big pulley just enough to pull the snubber out. Replace new snubber, tighten screws. Set drum back in place and reattach springs. Lean unit over and replace belt. Reconnect the small tube, back left corner. Replace the front panel and top. Connect the drain line and replace the rear panel. Connect waterlines and check for leaks. I went ahead and replaced all springs. I recommend replacing the belt while your at it. I'm wishing I would have. It runs like new, gets more water out on the spin cycle and the dryer dosn't take as long to dry the clothes.

I didn’t have special tool for brake but punch and hammer worked. Seal was easy to replace. Several videos online to show you how. It wasn’t worth it to tear apart the transmission and buy more parts/seals (if they were even available). But I didn’t know how much oil was in it. I drilled a hole in the side to somewhat check level and added 80-90 gear oil. It was almost empty and added almost a quart. Used a self taping screw/bolt with gasket sealer to plug the hole. I got 34 yrs out of this washer. If it fails, oh well. Just hate to buy a new one that only last 10yrs if im lucky.

Removed the screw from the side of the lid of the washer. Took off the old Lid Switch Actuator and screwed in the new one. Took a little elbow grease because the old screw was tight but no longer than 15 minutes tops.

After replacing the tub to pump hose, I adjusted the feet on the washer. Apparently, the main pulley sits so low on these washers that it ground into the floor and stripped out the thrust bearing. I ordered the new thrust bearing clip and put it in the evening I received it. The instructions it came with were very helpful and it was simple to reassemble. Up until the last piece - the retaining clip. The majority of the repair time was spent replacing that clip. If there is a tool that makes the job easier, I didn't have it. I finally got it on with two flathead screwdrivers prying the shaft out while I wedged one corner of the clip in the groove.

first remove drive belt then then remove dust cover on bottom of shaft take 5/16 nut driver to only 4 of the screws off that hold the brake cover on install 4 5/16 screws 1" long in those 4 spots.reomve rest of screws then slowly reomve back out 1" screws to relve spring pressure from brake pad.install all new parts from partsselect.com then install other part taken off in oreder and make your wife very happy

i took off the old belt and i took off the motor pulley with the pliers and srewdriver. i put the new pulley in with my hand and gave it a hit with the palm until it snap in and then i put the belt on by rotating the main pulley on tub till the belt was pulley on.

I removed the part that was still attached to the washer and installed the new flume. It took less than five minutes and a repair that would have cost over $85 cost less than $10 and I am no plumber!

I removed the plate at lower left corner on rear of washer 3 screws and it pops right off after that there are 2 clamps on the hoses attached to the pump I removed those with pliers then I removed the 3 screws holding the pump to the bottom of the washer then pulled the pump through the hole and replaced it with the new pump installed all the screws then layed washer on its side and replaced the belt set it up pluged it in and no more noise sounds better than new. Thank you Part Select for making it an easy painless task to get the parts I needed.

if you move the agiatater all the way to one side you can acess the star screws from under the hinge then push the agitator to the other side and acess the screw on the other hinge , you dont have to remove the top of the washer, let me say i did not have the serial no and the people at part select were very helpful and pacient when i called and they got me the RIGHT part the firdt time.thanks again for all your help the job came out perfect and saved me a lot of money for a repair man. ASHER

I opened up the top of the washer which exposed the tub, I took the top ring off the tub and under in side of the ring is the seal. Took the old one out and put the new one in. The old seal was completely wore out.
It was real easy.
Finding the part is usually the hardest part, but thanks to Parts Select finding the part was the easiest part of the repair.

The lid hinges are fastened to the top of the washing machine body, near the edge of the lid, with 1 screw each.
To remove the old lid hinges, with the lid clamped in the open position, I needed to gain access to the screw heads from underneath, just inside the edge of the lid opening. To get at these screw heads, I needed to push the inside wash drum toward the screw I wanted to remove and wedge something in the gap created between the body of the washer opening and the drum, directly opposite the screw that I pushed the drum towards. What? This is to hold the drum completely out of the way while getting at the screw. My wedge was the handle of a squeege that just happenned to be nearby, but just about anything will work.
Once the drum was secure, I was able to get at the screw head, which, by the way, is a totally blind operation; you cannot see the screw head, only feel it. I guess we're kind of used to feeling our way around these days. Anyway, I had to repeat the wedging thing to remove the other lid hinge.
The only real problem I had was the original (factory installed) screw heads were hex heads, and I struggled a bit finding the correct size allen wrench to blindly remove the screws. It is a good thing that I also ordered 2 new screws along with the new lid hinges because the new screws have phillips heads. Much easier to work with, even though they were a little pricey. The old hex head screws were kind of worn and it would have been a cursing operation to try to reuse them.
Once the old hinges were off, I removed the lid, installed the new hinges on the lid and clamped the lid in place in the open position, while I screwed the new hinges on (wedging the drum out of the way like before). NOTE: It might be a good idea to line the wash drum with newspaper in case a screw slips out and finds its way into one the holes in the drum; lost forever. Anyway, this may sound like alot, but it really isn't. My wife didn't even comment on how the lid isn't smashing down on her any more. That's OK, I'm grateful I'm not the one doing laundry!