41028 LG Washer - Instructions

Unplug washer!!! 1. Remove retaining ring around rubber gasket with flat head screwdriver. Just slightly pry off and it will easily come off. 2. Just peel back rubber gasket on the side that the lock is on. 3. remove 2 screws from the front off the lock assembly. 4. gently reach in and lift the little plastic clip holding the wiring harness and lift straight off. If the clip is lifted it might be a little tight just use even steady pressure to pull off. 5. Reverse these instructions to replace. Note: replacing the retaining ring on the rubber is a pain. The spring has to be in the bottom. Using a couple of flathead screwdrivers you can wrangle it back in place after awhile. There is a tool that looks like a large reverse pliers that may make it easier. Anyway thats it, pretty easy. There is a youtube video that shows all of this.

1) Shut off water supplies 2) Unplug 3) Disconnect water supplies from back of washer -some water will dribble out 4) Unscrew 2 screws at back of washer top plate (the lower of the two screws on each of the plastic bumpers) 5) slide top plate back a couple inches, then lift off. 6) Carefully stuff a towel underneath the distribution hoses and valves to catch any water that escapes during replacement. 7) Snap a photo of the entire area to help identify where the hoses and electrical connections are located to aid in re-connection (or label with tape). Be sure to note the color coding on the wires in relation to how they connect to the valves. 8) Pull the electrical connector(s) off the valve assembly 9) Use pliers to loosen and slide the hose clamps off as many of the hoses as possible and pull the hoses off the valve assembly. Some hoses are hard to reach, and can be removed after the valve is detached from the washer housing. 10) Unscrew the two screws from the back of the washer body holding the valve in place. 11) Remove the valve (and any remaining hoses). 12) Attach distribution hoses to new valve 13) Place new valve into washer body and screw into place. 14) Reattach electrical connection(s). 15) Remove towel and check for any stray water 16) Place top cover on washer and slide forward to lock in place. 17) Replace screws in top cover at rear of washer (unless you plan on checking for leaks after testing) 18) Reattach water supply hoses 19) Turn on water supplies 20) Plug washer in 21) Run washer self-test to check that all water inlets operate -see note at end 22) Check for leaks at water inlet hose connections and underneath washer OPTIONAL but ADVISABLE: check for internal leaks - 23) Unplug washer 24) Remove top cover 25) check for leaks at distribution hose connections 24) Replace top cover 25) Secure screws in top cover 26) Plug in washer NOTE: Washer self-test instructions: Turn washer off. Press and hold the SPIN SPEED and SOIL LEVEL buttons simultaneously, then press POWER button. Keep holding SPIN SPEED and SOIL LEVEL buttons until buzzer sounds twice. Release buttons. Press START/PAUSE button 4 times to test prewash inlet and listen for sound of water entering the washer. Press START/PAUSE button again for main wash inlet, press again for hot inlet, press again for steam inlet, press again for bleach inlet. Press 4 more times to get to drain cycle and watch for water to drain from tub (if any visible). Press 3 more times to turn test off. Power off washer to reset.

The repair went well and your parts are easy to find. This is the second time I have used your services and both times have been great. Your parts are at great prices and your delivery is a lot faster that one would think.
Thank you

Opened rear compartment of washer and observed problem with drum shaft slipping inside of plastic motor assembly. The plastic teeth used to secure drum shaft were worn down. The part I needed was sent as an assembly but should have been sent separately for a much lower cost? The new part looked like it was of a sturdier design. All in all I saved hundreds of dollars repairing the washer my self. The woman I spoke to on the phone was really nice and very helpful.

1.open back of washer with screwdriver. 4 screws total. 2. Remove assembly with 17 mm socket. 3. Install new rotor assembly with socket. 4. Replace back of washer with sscrews. 15 minutes total time.

Removed lid (top of washer), then ran a cycle in normal to identify the failed component, then noticed the water inlet valve assembly for the hot water was leaking, used my pc and went to website Part Select and found to failed part on the parts break down item, then ordered the part, the part "Valve Assembly Inlet" for the hot water arrived 2-days later, replaced valve in less than 5-minutes, disconnected push on electrical connector, unscrewed the valve assembly inlet and installed the new valve assembly inlet, very easy

pulled off top of washer to get at the inlet valve disconnect two hoses take two screws out and then you put it back together the way you took apart and your done

Unplug Washing machine first. Then remove 2 screws at the back of the top cover. Slide the top cover back then lift and remove. Unplug electrical connector @ inlet valve and remove water lines 1 going in and 1 out of valve. Remove 2 screws holding assembly in place then install new valve assembly and all other components in reverse order.

I watched a YouTube video on the repair and I was fully prepared.the repair went easy

removed top, removed 2 screws, replace part. did not fix problem, the real problem was the water inlet valve, works great, easy fix. thanks

This was very easy to instal. The aplaiance repair co. wanted $240 my LG is six years old and would rather buy a new one if I had to spend that much, so I gave it a shot and it took me 20 min to install the part. Told my wife she owed me $ 180 for my labor.

The bellows hose on the bottom of the tube had worn through where it flexed. This was an easy job except for the long reach you had to make under the washer to reach the hose clamps that held the part in place. These were spring loaded clamps which were easy to remove with pliers. I replaced them with ones that could be tightened with a socket wrench since it was hard to replace the sprung clamps.

It was so easy. i searched my model it brought up this site and the most common problem popped up without my even asking and recommended the part. i got it one week later and it was so simple to fix. a repair man wanted three times the part price to come to my home twice and would have had to wait longer. you guys were very helpful

took out the drain pump and replace with a new one

The problem ended up being the pump motor which discharges water from the washer. I figured out this was the problem after trying several things. I determined the motor was fine when it was empty. With the unit turned off, if you can rotate the tube with a quick spin and it lights up, probably this is OK. Then I tried to run it again and it went about 1/2 way through the cycle and stopped and started humming again. So I started emptying out the water, which I noticed was about 5 gallons which is way too much. so once empty, I took the pump off by turning unit on side. There are two hoses with hose clamps, and a few screws. Be careful to mark which wire plugs onto which side of the pump. One is brown and one is black. If you take the pump housing off, with the 3 screws, you should be able to pull the motor apart. Mine had water and scum from the wash in it, which was a dead give away that it was the problem.