F1069FD6 LG Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steven from Atlanta, GA
- Parts Used:
- AJQ73413811
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Very loud spin because of bad bearings.
I first tried to replace just the tub bearings (and the shaft seal) but found it impossible to get the old bearings out of the old outer tub. Partselect.com made the return easy and I ordered the rear outer tub assembly, which includes bearings already installed. For the most part, you have to completely disassemble the washer, removing the entire outer tub. If I had to do it again, I would order a new seal for the outer tub as well. The hardest part is getting the tub back together inside the unit. It really helps to have a helper.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Billings, MT
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
pump not working, moter run, propeller was detached from shaft
Removed the top, the front, got to the pump, removed it and replace it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jody from San Jose, CA
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Washer Would not drain
Found the part of Part Select by describing the problem. used a Utube video and step by step we were able to take apart, replace and put back everything with just a screw driver - I saved so much money!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allan from Virginia Beach, VA
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Washer not spinning and giving error message OE
Found on line OE meant washer not pumping out water with the suggestion to clean the filter and inspect the pump and lines for blockage. No problems there. You must be careful to empty the water manually before removing the filter. My wet vac helped but I still made a mess. I found a mechanic to look at the washer. He said it is common for the pump on these washers to go bad, especially if the washer has sat out of service. They wanted $300 to replace the pump. I found the part on this website for $53 and replaced it myself. The only hard part was emptying the water without making a mess and leaning the washer up and back far enough safely to remove the pump, then working on my back under the machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dion from Middletown, DE
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
R&R Drain Pump
The pump is apparently used for more than one washer, and the R&R instructions may be significantly different. I found a youtube video for my exact washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Ogdensburg, NJ
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Water not draining from tub, error code "OE"
Found great Youtube video, followed step by step. Only difficult part was getting the tub gasket clamp back on. But all in all pretty easy. If tub won't drain and weird noise coming from pump do not hesitate to do it yourself and save some coin!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darryl from chicago, IL
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Cloged Drain
My washer would try to spin and remove the water according to the time allowed. Consequently my washer would take longer than the time allowed to drain therefore water would send a code error then the machine would stop working. So I remove the hose from the pump and found my son's little small sock blocking the drain. I removed the sock and reinstalled all hoses. Everything is fine now. No need for a replacement item. Just a little servicing.
Was this instruction helpful to you?
Thank you for voting!