WT1801HWA LG Washer - Instructions

I noticed that my washer was leaking water into the tub. It was dripping, very slowly, but it was dripping. I noticed first, because it was starting to smell, and I didn’t understand why. Once I noticed that it was dripping, I checked online and noticed that the solenoid water inlet is most likely the problem. I found the part on parts, select, and confirmed with my model. The pictures were very close and similar, so I was pretty sure I was getting the cracked part. Once I received the part, it was time to fix it. You just have to turn the water supply off, remove the inlet lines with a adjustable wrench, if necessary, and then get to the washer. Make sure you also unplug the washer. There are only two Phillips head screws to remove to get the vanity cover off of the back. For whatever reason my removal was a little bit difficult for this. There are some plastic clips that hold the front portion on of the vanity plate. These were very tight, and I was afraid I would break them, but eventually they came loose with gentle upward pulling. Once this was off, it was super easy to identify the part that needed replacement. There are two hose clamps that you just need a pair of pliers to squeeze in slide off the hose. Then you remove three additional Phillips head screws, and the other connections pop out on their own. The solenoid plugs are very simple to slide off, and it is really difficult to put them on any other way. If you need to, you can take a few photos of the installation. Once you have the old one out, hook up the hoses first, and slide the hose clamps back to their original position. Once you have the two black hoses back on, reposition the new valve body, and slide the additional three prongs into the inlet soap dispenser. Make sure that the fit is snug. Don’t over push, the parts are plastic. Once this is done, reinsert, the three Phillips screws into their holes. Then you can reconnect the solenoids. At this point the replacement is done, and all you have to do is replace the vanity cover. Take time to ensure that you’ve done this correctly. I left the vanity cover off and ran a test load of dirty clothes to make sure that there were no leaks. Once I assure, there were no leaks, I put the vanity cover back on and put the two screws on. This was a very easy fix. Again, just go slow removing the vanity plate so you do not crack or break the tines in the front.

After unplugging the washer I cut the water off. I took the water hoses off, then the back top panel using a phillips head screw driver. I then used a pair of pliers to take off the two hoses and clamps. I unplugged the electric connection on each solenoid, took out 5 screws replaced the part and did everything in reverse order. Problem solved. Thanks for the fast service on my order.

I can’t really say it was easy and I just did it

Everthing went to plan except the wet side of the parts removal was difficult. used puller to remove the wash plate and got it to release. But the plastic part of the wash plate released and left the aluminum part still on the coupling. Corrision was the problem, and I had to again use a puller to remove this part of the wash plate. So it wasn't a matter of just lifting the wash plate off by hand. The rest of the replacement was fine.

I first fixed the stator coil by repairing the cut coil spots at 2 location using solder and with a bit of equivalent wires to extend with heat shrink sleeving to extend over the iron core. Next, I assembled the new coupling in the new coupling assembly with a bit grease around cogs. Wached few videos to see orientation since mine was broken assembly and wasn't certain how it sits inside. Once oriented and seated right, I wiggled to sit in properly over the stator cog..I felt the stator cogs with coupling locked to the shaft. After that I secured the main nut and connected the appliance. All worked perfectly after that. Thanks for sending the ordered parts. Now the washing machine is strong and solid in its agitation.

Our Samsung HE washer started making a grinding noise and stopping at the end of the rinse/spin cycle. I had replaced the clutch and seal 2 years ago and it sounded like it was going out again, however we were not getting the gunk inside the tub like before (seal) and the machine was throwing the tE error code when it stopped which it did not do last time. According to the manual this meant a thermistor error and the solution was "Call for Service". The machine is 9 years old and way out of warranty so....uh No! I ordered the new thermistor for $15 plus shipping to correct the tE code before looking to replace the clutch again or get a new machine. The new thermistor arrived, leaned the machine on its back, unplug one connector, remove two screws and pull the old one out of it's hole, push the new one in, replace two screws and the connector and GO! Problem fixed! No tE code, no stopping, no grinding noise. As best I can tell, the old thermistor was faulting during the spin cycle and the machine went into emergency stop mode which made the grinding noise. It was not the clutch or bearing at all. Most of the repair time was moving the machine out and disconnecting lines so I could lean it onto its back. Note: If your machine is stopping before draining, it will have water inside the tub which will drain out of the hole where the thermistor goes when you pull the old one out. It has an o-ring to seal it, so just expect a little water to come out and be ready to catch all the water or put the new one in quickly.

The base assembly was easy to repair tip the washer on its side and took the screws out the bottom and two wires and a sensor off the old base assembly that was broken and replaced it the the way I took it off easy install. And they got great costumer service as well will be back for other parts.

unplugged machine, turned off water valves. Moved machine away from the wall. Disconnected supply lines. Removed cover housing water valve assembly.
Took a picture with phone. Disconnected water and electrical wires. Removed water valve assembly . Installed new assembly ,cover and reconnected supply lines, plugged power cord in, turned on water supply valves. Done.

Tried to remove adjitator but it was stuck. Could not find any professional method of pulling it. There must be some type of puller,

Very close to the installation video online at Parts Select. Removed the back panel, unclipped the hose from the inner fitting and replaced with the rear hose. Why it didn;t leak on the inside is interesting as there was no clip on the at the inner fitting.
The one difference from the existing install video online was that I didn't have to tip the washer over ~75 degs before replacing. I instead found that I could put to cinder blocks under the back edge to replace the drain hose. This made the job quicker without having to worry about having a box for it to rest on (with any risk of falling to the floor).

Since the old pulsator had actually come off during a wash cycle, I was able to place the new one on easily. Tightened the screw with a socket. Then placed the new cap on. Before placing the new pulsator on, I was able to clean all the mold and hard deposits off the mechanism under the pulsator. The hard deposits were also scrapped from the pulsator holding (where the screw goes) which may have caused the problem to begin with.

Tried everything and could not get it out I just use mesh bags for washing at this time, but LG washing machine is the worst I have ever had

Former LG repair looked under washer while it was engaging & noticed motor was not spinning. LG took forever I ordered the part from you guys. It looked different from original. Figured out to take extra port for front loader. I have top loader. Installed washer works great!!

Very simple repair after watching YouTube video on how to complete repair.

I HAD A CHAT WITH LG EXPLAINED THE PROBLEM . SAID IT WAS THE WATER SHUT OFF VALUE. V EVEN SENT THE PAGE WITH PART# TO ORDER ONLINE.

LOVE LG CHAT!!!