41482 LG Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ryan from HIGHLAND, UT
- Parts Used:
- 4738ER1004B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Noticed small tear in hose bellows and leak during reassembly
I already had the top of the washer open, from previous disassembly to clean the front loader seal, and when I ran a trial load, noticed a small 1/4" tear in the hose bellows that attaches to the drum.
Very simple repair, remove the existing hose by loosening the clamps, paying attention to their orientation. Install the existing hose clamps onto the new hose, install and tighten the hose clamps.
5 minute job, if the washer top is off (which is also simple).
Very simple repair, remove the existing hose by loosening the clamps, paying attention to their orientation. Install the existing hose clamps onto the new hose, install and tighten the hose clamps.
5 minute job, if the washer top is off (which is also simple).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from LA CROSSE, VA
- Parts Used:
- 3891ER2003A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
soap dispenser broke
just put new part in very simple only problem was shipping yall used fedex went to 4 states and one state twice they finally gave it to USPS so it took almost 9 days to get here
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from GOLD BAR, WA
- Parts Used:
- 3891ER2003A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Soap dispenser
Replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from CLEVELAND, TN
- Parts Used:
- 5220FR2006H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The hot water inlet valve started to leak.
To fix the problem, I simply removed the top cover of the washing machine by removing the two screws on the back of the machine which allowed me to slide the top back and then I lifted it off. Then I disconnected the hot water hose (after shutting off the valve). Next, I removed the electrical connectors on the old part as well as the hose attached to it and unscrewed the old part and removed it and put the new one on and reattached the hoses and the electrical. It worked like a charm. It took me perhaps 10 minutes total.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from COLUMBUS, OH
- Parts Used:
- 5220FR2006H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Broke cold water inlet while moving
Replaced cold water inlet. Removed 4 water lines and 5 wires put new part in and reinstalled lines and wires
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from KERRVILLE, TX
- Parts Used:
- 5220FR2006H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Hot water valve was leaking
After I watched the repair video for the part, it was a snap. It went exactly as the video described the steps. Hardest part was moving the washer to get behind it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tiffany from PUYALLUP, WA
- Parts Used:
- 5220FR2006H, 4738ER1004B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Our washer was leaking from the washer hose. Once taken off I could see it had a small tear in it. All it took was a screwdriver and a couple minutes and we were up and running. I love PartSelect.com for always having the parts I need and getting them to me in a timely manner!
Took off the old hose with a screwdriver and put the new one on. As simple as that. You don’t need a repair man to get this done, you can do it yourself and save money too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rudy from SAN DIEGO, CA
- Parts Used:
- 5220FR2006H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Hot water inlet had leak, kept filling washer, when offw
When to utube typed in my problem, very easy fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Castle Rock, CO
- Parts Used:
- 4738ER1002A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The tub-to-pump hose was leaking.
I tipped the right side of the washer up 9.5 inches using two 2x4s and I was able to remove and replace the old hose with the tools described.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALEX from TULARE, CA
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Washer was not draining
It was giving me a code got on YouTube it gave the code after that bought a new pump and fix done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Myles from Kingston, NH
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Drain water was not being fully pumped out, leaving foul water in the tub and wet clothes smelling like sewage.
I removed the top of the washer, pried the front control panel off (pull a couple of electrical connecters or just rest it on something), separated the tub sleeve from the front panel and then removed the front panel (two screws). To remove the pump - just remove a couple of hoses, two wires and slide it out of the clip below. Reverse the process to install. A little daunting if you haven't done something like this before, but easily do-able once you get past your fears. A service call would cost much more than the $60.00 it took to get the part to my front door. This worked out really great - my wash smells fresh once again and my wife has moved on to the next project on her honey-do list!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from FENTON, MI
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Washer would not drain.
I followed the video and it was quite simple. There was an extra sheet metal screw at the bottom of the front panel which kept it from coming free of the three tabs. On the two pump wite connectors I made a mental note that the black wires were on top. The repair also fixed the lack of water flow through the degeterent dispenser. I was afraid of putting the tub seal back in place as a pro struggled with it when it was new and under warranty. It really was no problem at all. Take some phone pics along the way boosted my confidence.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynly from Montrose, CO
- Parts Used:
- 3891ER2003A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bought used, realized did not have a detergent dispenser.
Found this part online. I just sets inside, did not click in like the bleach and fabric softener inserts. Think is ok, seems to work
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from DEMING, NM
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Error code "EO", Drain Pump not working
I followed the video on the PartSelect web site for this repair and it went just fine. I also replaced the drain hose while I had everything apart. Thank you PartSelect, same day shipping. Arrived within 3 day's and your video was spot on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Pie Town, NM
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Pump stopped working
Followed the video instructions provided.
Was this instruction helpful to you?
Thank you for voting!