WM4070HWA LG Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Denise from LAS VEGAS, NV
- Parts Used:
- 5220FR2075L
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Leaking from 19 yr old cold water valve.
Figured out how to take off top of washer, look inside for problem, ordered new part, watched video how to replace part. All on line. $65.00 later and my 19 yr old washer is still working awesome.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne from MONROE, NY
- Parts Used:
- AGM73610701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Magnetic door plunger broke off, then got stuck inside the door and couldn't be removed for replacement.
I used another magnet to pull the old plunger out of the door and replaced it with the new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from IOWA PARK, TX
- Parts Used:
- AGM73610701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door plunger had a broken tooth and would not stay in place.
Just put in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from BOTHELL, WA
- Parts Used:
- AEG33121501
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
TE error. Replaced heater / thermistor assembly.
removed top and front. heater is at the base of the tub. the nut compresses the rubber seal and may take some wiggling to remove the old one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harley from OKLAHOMA CITY, OK
- Parts Used:
- 5220FR2075L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
water failure
followed video exactly and it worked perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SOMERSET, KY
- Parts Used:
- 5220FR2075L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer was putting water in tub when it was in the spin cycle
Unpluged -shut off water removed 2 screws on lid,removed lid took 2 screws out holding part on swapped the hoses out and pluged wires in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from PITTSBURGH, PA
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Drain pump inoperable
1 tilt washer back
2 remove cover plate screw from front of drain filter access panel.
3 Remove cover plate and remove 2 more mounting screws .
4 go below washer and pull down sliding clip and move pump assembly back.
5 remove wires and 3 mounting screws around pump housing
6 Swap pump and re-attch wires
2 remove cover plate screw from front of drain filter access panel.
3 Remove cover plate and remove 2 more mounting screws .
4 go below washer and pull down sliding clip and move pump assembly back.
5 remove wires and 3 mounting screws around pump housing
6 Swap pump and re-attch wires
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from SMITHVILLE, TX
- Parts Used:
- AGM73610701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One Plunger latch broken off.
Line up the plunger with the existing slots in the door and push in.
NOTE: When testing it was evident that the magnet was not as strong as the original one. I would rate as one step up from useless.
NOTE: When testing it was evident that the magnet was not as strong as the original one. I would rate as one step up from useless.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobbie Joan from ASHEVILLE, NC
- Parts Used:
- AGM73610701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door would not close because the part that was in the door that held it closed kept falling out.
Order the part through PartsSelect. It arrived in a few days and I (an 81 year old woman) replaced it within minutes with no help needed. It was super easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fredrick from KAYSVILLE, UT
- Parts Used:
- 5220FR2075L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Cold water inlet valve was leaking where solenoid attaches to valve body.
Hardest part of the job was getting the washer away from the wall. :)
Disconnect power & water
Remove top panel, two screws at back
Remove two screws holding valve to washer body
Use pliers to loosen and pull back spring clamps on three water tubes
Remove tubes by twisting and pulling
Reverse process to install new valve.
I am convinced that the original valve began leaking because I had heard water hammer for years as that valve opened and closed during operation. I bought two water hammer arrestors (less than $30) that attach inline with the inlet hoses and I think that will prevent the problem from recurring.
Disconnect power & water
Remove top panel, two screws at back
Remove two screws holding valve to washer body
Use pliers to loosen and pull back spring clamps on three water tubes
Remove tubes by twisting and pulling
Reverse process to install new valve.
I am convinced that the original valve began leaking because I had heard water hammer for years as that valve opened and closed during operation. I bought two water hammer arrestors (less than $30) that attach inline with the inlet hoses and I think that will prevent the problem from recurring.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from ORR, MN
- Parts Used:
- 5220FR2075L, AGM73269501, 5220FR2006H
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Hard water scale rendered the valves inoperable
Watched a YouTube video on valve replacement. Then when I knew what to expect, the repair job was a breeze.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from CARNEGIE, PA
- Parts Used:
- 5220FR2006H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Dishwasher would not fill
Used Youtube to look for a set of repair instructions. From start to end 35 min.
The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.
Overall very easy to do.
The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.
Overall very easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christen from HUMBLE, TX
- Parts Used:
- 5220FR2006H
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench (Adjustable)
The hot water valve was leaking
It went great. First of all, thank you Part Select for the video on how to do this myself. My home warranty company was giving me a hard time. Blah, blah, blah. A mechanic friend of mine referred me to this site. Within minutes I found the part I need and a GREAT!!!! price. Ordered it, got it super fast, fixed it my self and my second hand washer is no longer peeing all over the floor. Very very happy. I will definitely be a repeat customer, hopefully not anytime soon.
Thank you again for an amazing experience.
Thank you again for an amazing experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from HEREFORD, AZ
- Parts Used:
- MDS47123608
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Rubber door gasket had traces of mold due to door not being left open after use. Washer smelled bad also
Got new door gasket, watched several Youtube videos of repair process. Followed several combinations of the process, which were accurate and it went ok. Met with the described difficulty re-installing the boot due to the spring installation. The use of vise grips for the second spring was the best piece of advice, as the spring tool did not work for that specific process. Door did not want line up exactly the way it came off, causing some concern about the door lock, and possible leaking. After install, it seems to work ok on those accounts. Have only run large bulky items since, which cause many "OE" issues. have not tried a normal load yet, but I think it will be ok.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from SCOTTSBORO, AL
- Parts Used:
- ACA56078801
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Instructions on how to turn Clamp counter clockwise to get back on tube assembly
Watched videos but didn’t show the clamp had to be placed on counterclockwise
Was this instruction helpful to you?
Thank you for voting!