Models
>
WM4070HWA
WM4070HWA LG Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for WM4070HWA
Viewing 3 of 3
Keep searches simple, eg. "belt" or "pump".
$74.11
This is a drain pump motor assembly for washers. This OEM part is responsible for removing water from the washer during the drain part of the cycle. When this part is clogged, damaged or defective it ...
In Stock
Order within the next 3 hrs and your part ships today!
$26.80
The hot water valve is found at the back of your washer and controls the flow of hot water into the machine. If the valve is defective, the washer may leak, overfill, fill slowly, or not fill with wat...
In Stock
Order within the next 3 hrs and your part ships today!
$24.28
The magnetic door plunger is used on your washing machine to keep the door open when not in use. This allows for the inner door and tub seal to dry thoroughly, which helps to prevent any buildup of mo...
In Stock
Order within the next 3 hrs and your part ships today!
$63.71
The tub bearing supports the spin basket shaft at the back of the washing tub. If your washing machine will not spin, is leaking water, or if there is a loud screeching noise during the wash cycle, th...
In Stock
Order within the next 3 hrs and your part ships today!
$38.18
This hose has bellows to allow for flexibility during the wash and spin cycles.
In Stock
Order within the next 3 hrs and your part ships today!
In Stock
Order within the next 3 hrs and your part ships today!
$38.18
This is a replacement sensor assembly for your washer. It may also be known as a motor rotor position sensor. The sensor assembly monitors the direction and speed of the spinning rotor and communicate...
In Stock
Order within the next 3 hrs and your part ships today!
$27.79
This is a replacement detergent dispenser for your washer. It stores the detergent, and then dispenses it into the washer at the appropriate point in the wash cycle. If the detergent dispenser is brok...
In Stock
Order within the next 3 hrs and your part ships today!
$31.32
This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose conne...
In Stock
Order within the next 3 hrs and your part ships today!
$14.48
The locking pin is used to hold the shock absorber on the washer. There is a pin used at the bottom and top of the shock absorber. Sold individually.
Special Order
$26.76
This replacement pump filter, also known as a filter assembly, is a genuine OEM part for your washer or washer/dryer combo. Before beginning this repair, turn off the power and water supply to your wa...
In Stock
Order within the next 3 hrs and your part ships today!
$8.04
This drain hose plug, also known as a hose cap, is a genuine OEM part for your washing machine. This plug caps the drain hose from the pump housing, and helps prevent leaks from your washer. Before be...
In Stock
Order within the next 3 hrs and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for WM4070HWA
Viewing 14 of 14Will not drain
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Lid or door won’t close
Fixed by these parts
How to fix it
Does not dispense fabric softener or detergent
Fixed by these parts
How to fix it
Will not agitate
Fixed by these parts
How to fix it
Draining Issues
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Engine runs but does not pump water
Fixed by these parts
How to fix it
No hot or cold water
Fixed by these parts
How to fix it
Water Filling Issues
Fixed by these parts
How to fix it
Spinning Issues
Fixed by these parts
How to fix it
Spins slowly
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Noisy and Marks Left on Clothes
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jorge from Apple Valley, CA
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Washing maching wouldn't drain
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer cam
... Read more
e apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Harrisburg, PA
- Parts Used:
- 6501KW2002B
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
LE Error Message and won't spin drum properly
I first tested the motor per the service manual. I checked the resistance between the terminals of the 3 pin connector. It's supposed to be 5-15 ohms. The motor checked out so I replaced the main electrical board. It turns out that wasn't the problem. After a brief web search I found out that the hall sensor (which is attached to the
... Read more
motor stator) was the likely cause of the failure. I replaced that and everything works great now. And now I have a spare main board in case that ever fails. I also want to mention that I took the time to remove the dispenser box (where the water comes in and is directed to the different cleaning products) and cleaned it with a very strong bleach solution. It got rid of the mildew and funky smell. It seems that the fabric softener caused a lot of mildew to form inside the dispenser directly above the fabric softener tray. The bleach took care of that. This is probably something that should be done routinely to keep the mildew from forming.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Omnitech from Warrenville, IL
- Parts Used:
- AGM73610701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door would not close
There is a magnet at the bottom of the door which allows the door to be held ajar when the washer is not in use to allow the tub and gaskets to dry. A tab on the plastic housing which retains the magnet broke which allowed the housing to pull free of the door and stick itself to the machine preventing the door to close. Easy fix to replac
... Read more
e the magnet was $18. Instructions were included in the box. Part number on the drawing was A165. PS3618292 Magnetic Door Plunger
Read less
Was this instruction helpful to you?
Thank you for voting!