WM2450HRA (ACREEUS) LG Washer - Instructions

Took off the old one and put the other one on. The only difficulty was that my husband has big hands and had a hard time getting to one end.

Hardest part was getting the correct part. Due to some glitch somewhere there was a mix up in the database for the correct pump number. This unit has two pumps mounted to the same housing. One is a recirculating pump and one is discharge pump. I ordered the discharge pump and kept receiving the recirculating pump. Discharge pump is LG PART#4681EA2001T and recirculating pump is LG PART #4681EA2002H Once in hand the install went fairly smoothly. Removed top - two screws on back of unit. Removed control panel with one screw on upper right inside corner, associated plugs and snap clips. Removed soap tray and drained water through filter tube. Removed screws in front of filter. Using Vise grips stretched spring from around front seal. Removed screws holding front of washer to top frame (2?)[accessed after soap tray removal]. Pump assembly located in bottom left, removed associated hoses, Marked wired colors on pump housings and removed. Removed assembly. Unscrewed pump, installed new pump and reversed procedure to reassemble. Struggled mostly with replacing spring around front seal. Stretch it as far apart as you can as you "roll" the spring in and then massage the seal to get the spring into correct position. Definitely a doable repair. Good Luck.

1) Shut off water supplies 2) Unplug 3) Disconnect water supplies from back of washer -some water will dribble out 4) Unscrew 2 screws at back of washer top plate (the lower of the two screws on each of the plastic bumpers) 5) slide top plate back a couple inches, then lift off. 6) Carefully stuff a towel underneath the distribution hoses and valves to catch any water that escapes during replacement. 7) Snap a photo of the entire area to help identify where the hoses and electrical connections are located to aid in re-connection (or label with tape). Be sure to note the color coding on the wires in relation to how they connect to the valves. 8) Pull the electrical connector(s) off the valve assembly 9) Use pliers to loosen and slide the hose clamps off as many of the hoses as possible and pull the hoses off the valve assembly. Some hoses are hard to reach, and can be removed after the valve is detached from the washer housing. 10) Unscrew the two screws from the back of the washer body holding the valve in place. 11) Remove the valve (and any remaining hoses). 12) Attach distribution hoses to new valve 13) Place new valve into washer body and screw into place. 14) Reattach electrical connection(s). 15) Remove towel and check for any stray water 16) Place top cover on washer and slide forward to lock in place. 17) Replace screws in top cover at rear of washer (unless you plan on checking for leaks after testing) 18) Reattach water supply hoses 19) Turn on water supplies 20) Plug washer in 21) Run washer self-test to check that all water inlets operate -see note at end 22) Check for leaks at water inlet hose connections and underneath washer OPTIONAL but ADVISABLE: check for internal leaks - 23) Unplug washer 24) Remove top cover 25) check for leaks at distribution hose connections 24) Replace top cover 25) Secure screws in top cover 26) Plug in washer NOTE: Washer self-test instructions: Turn washer off. Press and hold the SPIN SPEED and SOIL LEVEL buttons simultaneously, then press POWER button. Keep holding SPIN SPEED and SOIL LEVEL buttons until buzzer sounds twice. Release buttons. Press START/PAUSE button 4 times to test prewash inlet and listen for sound of water entering the washer. Press START/PAUSE button again for main wash inlet, press again for hot inlet, press again for steam inlet, press again for bleach inlet. Press 4 more times to get to drain cycle and watch for water to drain from tub (if any visible). Press 3 more times to turn test off. Power off washer to reset.

I received the part needed within a few days from ordering. I immediately removed the leaking part with the new part. It was a very simple install, and my washer is now leak free. If you think you cannot do these simple changes, think again, it's much easier then you may think. Remove the top cover of your washer machine by taking off the two screws in the back. Remove the hose clamp with a pair of pliers and pull off from the intake valve, of course make sure your water valve is shut off before starting. Remove the two prong clip. Using your pliers, disconnect the main hot water hose. Use a Phillips screwdriver to remove the two screws that holds the valve in place. Remove and discard it and replace with the new valve. Follow the steps and your done, it's that easy....TC

Followed the instructions that a fellow DIYer posted in PartSelect and a few I watched on Youtube. Pull out the detergent drawer, remove the back screws, slide the top off, unclip the control board, unplug Power & One more switch so that I could move it aside. Take the gasket retention wire off the door gasket & tuck it inside. Remove the screws in the bottom & top. Then slide the front panel, including the door up (not easy) and out. The part received was only the pump motor so I had to take a few pictures before so I knew I got it together right. Remove drain houses, pump screws, slide pump back and remove pump. A few more screws to remove the pump from the housing & replace with new pump. Put it all back together. It works! It only took about 45 minutes

UNPLUG WASHER.Unscrew 4 screws holding silver plate at back of unit. Remove plate to expose inside of unit. Locate drain hose at bottom of washer tub. Hose connects at front drain, bottom of tub, and at rear at the pressure sensor. Front and rear simply slide clamps down by grasping clamp tabs and sliding clamp off connection point. Disconnect from tub bottom by loosening main clamp with Phillips screwdriver and pulling downward. Have a towel handy as there will be water in the hose, and it will pour out when removing it from the unit. Installation is the reverse of removal. ATTACH THE HOSE ASSEMBLY TO THE DRUM FIRST, THEN FRONT, THEN LASTLY REAR. This order is the easiest way, otherwise you will spend extra minutes trying to get the tub connection to seat properly. Plug it back in (duh), then you're good to go for another 4 years or so until another hole wears in the hose. I have performed this repair on 3 different units, with 4 years being the average lifespan of this part.

Tipped the washer on its side to expose the bottom, removed the plastic lid adjacent to the pump after removing the screws holding it , then, using a flat head on a pry tab pulled out the pump, removed the hoses with pliers to complete the extraction, swapped the pump on my bench. . assembly is reverse of disassembly. .

ordered part from Part Select and it was here very quickly,but the part came damaged (not the fault of Part Select). I ordered another one and PartSelect had it here the next day. I watched the video on how to replace it and it was very helpfull.The particular part I replaced (pump motor) does not seem very durable. I will buy an American made washer the next time I need one. I will use Partselect in the future and recomend it to others.

We drained the water from the washer via the tiny hose/filter located at the lower left corner of the washing machine. The unit was then pulled away from the wall, unplugged and the hoses disconnected. At this time, we used the wet dry vacuum to suction the water that remained in the drain hose. We tilted the washing machine back until the front of the unit was 18 inches or so off the floor. We used the foot stool to hold the washer up in the air so that we could work on the pump. Replacing the pump was as easy as removing a few screws, unplugging the electrical connections and removing the faulty pump assembly from the plastic housing. (Be sure to mark what connector goes in what terminal). Re-assemble. Re-connect. You are ready to go. It took more time to ready the washer than it did to replace the part.

Another friend of mine did the repair.I watched him remove the old Drain pump and Motor Assembly and the Circulation Pump Motor.He installed the new parts in 45 to 60 minutes. The washer works like a new one. I had never ordered from Parts Select before. I was amazed how fast I received the new parts. Order placed on line on Friday , received the order at my home on Saturday afternoon.I will tell my friends about Parts Select and I will buy from them in the future.

I watched a YouTube video on the repair and I was fully prepared.the repair went easy

Simply took hose off from inside machine and replaced it with new one. The tore one had a stopper on one end that wrapped to front machine; inside filter compartment. So I put stopper on the other end of new hose and wrapped it to it's holding spot in filter compartment.

The repair went well and your parts are easy to find. This is the second time I have used your services and both times have been great. Your parts are at great prices and your delivery is a lot faster that one would think.
Thank you

Removed lid (top of washer), then ran a cycle in normal to identify the failed component, then noticed the water inlet valve assembly for the hot water was leaking, used my pc and went to website Part Select and found to failed part on the parts break down item, then ordered the part, the part "Valve Assembly Inlet" for the hot water arrived 2-days later, replaced valve in less than 5-minutes, disconnected push on electrical connector, unscrewed the valve assembly inlet and installed the new valve assembly inlet, very easy

The problem ended up being the pump motor which discharges water from the washer. I figured out this was the problem after trying several things. I determined the motor was fine when it was empty. With the unit turned off, if you can rotate the tube with a quick spin and it lights up, probably this is OK. Then I tried to run it again and it went about 1/2 way through the cycle and stopped and started humming again. So I started emptying out the water, which I noticed was about 5 gallons which is way too much. so once empty, I took the pump off by turning unit on side. There are two hoses with hose clamps, and a few screws. Be careful to mark which wire plugs onto which side of the pump. One is brown and one is black. If you take the pump housing off, with the 3 screws, you should be able to pull the motor apart. Mine had water and scum from the wash in it, which was a dead give away that it was the problem.