WM3070RD (ACREEUS) LG Washer - Instructions

Replaced cold water inlet. Removed 4 water lines and 5 wires put new part in and reinstalled lines and wires

Watched the easy video instructions on the product page and did the same on our machine - pop off the top, unscrew the plate from the front of the door inset. Its a little challenging to unplug the old lock assembly because it is a tight fit and not enough room for two hands to fit to provide a bit more leverage when pulling the power lines out, but once its out it is easy to install the new one and reattach the strike plate frame and top of the washer. Plugged back in and we were back in business. This $50 part ended up saving us at least $300 in repair fees to get it working again.

Incredibly fast shipping - arrived in less than 2 days - which was really helpful as we were unable to use the washing machine until we were able to get this fixed. Excellent pricing as well. Couldn't be happier I found this site and the product I needed so easily.

Looked at videos on line at Parts Select. Very easy instructions to watch and follow. After unplugging the washer all I had to do was turn off the cold water valve, remove the supply line, two screws to get the lid off, then two screws to remove the valve and disconnected the electric connector tabs. Took pliers to back the three hose clamps off. The best tip was replacing each hose back on the valve one at a time to prevent mix ups. I did everything in reverse after installation. I ran one short cycle to test the leak. Works perfectly!
A tip I saw on You Tube - I have vinyl flooring in my wash room and a repair guy said to spray a light shot of WD 40 under the feet. It doesn’t take much. Man, my washer slid like it was on wheels! I wiped away any excess spray and let it dry under the feet. I’m not sure how this works on other types of floors.

I set my iPad on the exposed washing machine drum, was exposed after removing top as explained in video, and put on the ‘ how to do video it’. It was so easy for this 78-year-old brain, that I am very pleased with myself. Also would like to thank whoever I talked to, Chris, when I ordered this part from this company, Chris was very helpful and took time with me. So this ‘do it yourself person’, and I’m really not a do it yourself person, WILL certainly be looking into other do it yourself fixers. Thank you again.

Took off the old hose with a screwdriver and put the new one on. As simple as that. You don’t need a repair man to get this done, you can do it yourself and save money too.

Replaced it

To fix the problem, I simply removed the top cover of the washing machine by removing the two screws on the back of the machine which allowed me to slide the top back and then I lifted it off. Then I disconnected the hot water hose (after shutting off the valve). Next, I removed the electrical connectors on the old part as well as the hose attached to it and unscrewed the old part and removed it and put the new one on and reattached the hoses and the electrical. It worked like a charm. It took me perhaps 10 minutes total.

Ordered and replaced the hot and cold inlet valves - followed the instructions off of the video posted on the Part Select website ... completed the repair in less than 10 minutes

Found this part online. I just sets inside, did not click in like the bleach and fabric softener inserts. Think is ok, seems to work

All I did was first of all and since it is so heavy I put 2 furniture sliders under the 2 front feat because I had to pull it out from where it was onto the carpet and the back feat I just sprayed some wd40 so the would slide on the tile floor. Then I took the top off by removing 2 bottom screws and pulled the lid back and up and there was the cold valve. Next I pulled the electric tabs off. Don’t worry they go on the same way they were on. Do not at this time remove the screws on the valve until you pull each off one at a time and place one at a time back on the new valve. Then remove the screws and the old valve and put the screws back on for new valve and you are done. Replace cold water hose turn on water check if no leaks replace lid, you are as if new once again. Good luck. Cost for all that is around $50

Former LG repair looked under washer while it was engaging & noticed motor was not spinning. LG took forever I ordered the part from you guys. It looked different from original. Figured out to take extra port for front loader. I have top loader. Installed washer works great!!

Remove old one and replace. Just make sure it is all the way on and secure or you will have a huge mess on your hands.

Some screws, some clamps. Easy and straight forward. unplug machine, turn off water, disconnect water hose, unscrew top of machine (2 philips head screws), disconnect clamp from valve (use a towel for remaining water), disconnect wire, unscrew from place holder, remove entire valve, work backwards from there.

Pull the washer away from the wall to get behind it. Unplug the electrical power cord from the wall. I removed the top cover by unscrewing the 2 screws on the back of the washer. Slide the cover back about 1-2 inches towards the back of the washer and then lift the cover up and remove. It might be a little tight to slide back, you may need to wiggle the cover side to side or give it a good smack. The water inlet valve is directly at the top inside of the washer. I saw a slow leak dripping from the hot water inlet valve onto the back side of the drum. Turn off the water supply valve at the wall and then unscrew the supply water hose from the water inlet valve at the back of the washer. Disconnect the electrical connector and water hose from the inlet valve inside the washer. From the outside of the washer on the back, remove the screws holding the water valve and lift out the valve. Install in reverse order.

Unplug Washing machine first. Then remove 2 screws at the back of the top cover. Slide the top cover back then lift and remove. Unplug electrical connector @ inlet valve and remove water lines 1 going in and 1 out of valve. Remove 2 screws holding assembly in place then install new valve assembly and all other components in reverse order.