Models
>
WM8980HVA
WM8980HVA LG Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Models for WM8980HVA
Click on the best match to narrow your results.
- WM8980HVA (ASSEEUS) LG Washer (Model Lg Wm8980hva.Asseeus 5.2 Cu. Ft. Mega Capacity Smart Wi-Fi Enabled Front Load Washer With Turbowash And Built-In Intellig – Common Parts And Diagrams)
- WM8980HVA (ASSEEUS) LG Washer (Model Lg Wm8980hva.Asseeus 5.2 Cu. Ft. Mega Capacity Smart Wi-Fi Enabled Front Load Washer With Turbowash And Built-In Intellig – Common Parts And Diagrams)
Diagrams for WM8980HVA
Viewing 3 of 3Keep searches simple, eg. "belt" or "pump".
$19.63
Hold the door slightly open between loads, allowing air to circulate through the drum and around the door seal with this washer magnetic door plunger. This helps trapped moisture dry and reduces musty...
In Stock
Order now and your part arrives by Nov 23
$67.26
Water leaves the washer tub through this flexible tub-to-pump drain hose before reaching the drain pump housing. Its corrugated bellows section bends with tub movement, helping maintain the connection...
In Stock
Order now and your part arrives by Nov 23
$43.95
The suspension shock absorber connects the tub to the cabinet base and resists sudden movement as the load turns. A worn or damaged absorber may allow excessive shaking, thumping, or repeated unbalanc...
In Stock
Order now and your part arrives by Nov 23
$43.95
Water and detergent travel from the dispenser into the washer tub through this flexible rubber dispenser hose. Its bellows folds allow the hose to flex as the tub moves during operation, helping maint...
In Stock
Order now and your part arrives by Nov 23
$38.45
The removable filter and cap assembly provides access for routine cleaning and seals the filter opening when tightened. Replace the damaged assembly to restore the debris trap and sealed access point....
In Stock
Order now and your part arrives by Nov 23
$26.19
The locking pin is used to hold the shock absorber on the washer. There is a pin used at the bottom and top of the shock absorber. Sold individually.
Special Order
In Stock
Order now and your part arrives by Nov 23
$16.45
This hose clamp applies pressure around the hose end, holding it firmly against its fitting during operation. A secure hose connection helps keep water contained inside the appliance. This OEM part is...
In Stock
Order now and your part arrives by Nov 23
$157.25
If your washer isn’t locking or starting like it should, this replacement door lock switch could be the fix you need. It helps your machine know when the door is closed so it can lock and begin the cy...
In Stock
Order now and your part arrives by Nov 23
$23.05
Drain residual water before cleaning the pump filter with this washer cleanout hose. The flexible rubber hose attaches to the drain pump filter housing, giving remaining water a controlled outlet from...
In Stock
Order now and your part arrives by Nov 23
$52.75
Separate wash water from the rear tub bearings with this washer seal. Fitted around the rotating drive shaft, it maintains contact while still allowing the shaft to turn, helping protect smooth drum m...
In Stock
Order now and your part arrives by Nov 23
In Stock
Order now and your part arrives by Nov 23
Common Problems and Symptoms for WM8980HVA
Viewing 8 of 8Leaking
Fixed by these parts
How to fix it
Lid or door won’t close
Fixed by these parts
How to fix it
Locking Issues
Fixed by these parts
How to fix it
Shaking and Moving
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Spinning Issues
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Water Filling Issues
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Omnitech from Warrenville, IL
- Parts Used:
- AGM73610701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door would not close
There is a magnet at the bottom of the door which allows the door to be held ajar when the washer is not in use to allow the tub and gaskets to dry. A tab on the plastic housing which retains the magnet broke which allowed the housing to pull free of the door and stick itself to the machine preventing the door to close. Easy fix to replac
... Read more
e the magnet was $18. Instructions were included in the box. Part number on the drawing was A165. PS3618292 Magnetic Door Plunger
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from STOWE, VT
- Parts Used:
- 4738ER1002A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
leaking tub-to-pump drain hose
Pull washer away from wall. Unplug cord and remove drain hose from receptacle. Remove 4 screws holding panel to rear of washer. Squeeze and slide back hose clamps on each end of drain hose and loosen center clamp with screwdriver. Remove old hose. Reinstall new hose in reverse order using existing clamps. Re-install back panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from AUBURN, CA
- Parts Used:
- AGM73610701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plunger fell out broken tab.
Just aligned and pushed in.
Was this instruction helpful to you?
Thank you for voting!