W3S1CVK2EHM (ABLEEUS) LG Washer - Instructions

Watched videos but didn’t show the clamp had to be placed on counterclockwise

An appliance repairman determined the problem which was that it needed new pulleys and thankfully PartSelect carried them. He installed them in an hour and my dryer runs fine now.

I already had the top of the washer open, from previous disassembly to clean the front loader seal, and when I ran a trial load, noticed a small 1/4" tear in the hose bellows that attaches to the drum.

Very simple repair, remove the existing hose by loosening the clamps, paying attention to their orientation. Install the existing hose clamps onto the new hose, install and tighten the hose clamps.

5 minute job, if the washer top is off (which is also simple).

Followed video provided on site

Unscrewed the sensor cover, which on this model also holds the lint filter in plas. Then pulled the old sensors from their plug-ins. The new sensors easily slipped into the holder, and then replugged to the wires. The whole assembly screwed back into place. One note of caution: the flap where the filter slides in goes inside the cover, it's default is not upright, and be careful to not allow the inside spring for the cover to come off, or you might chase it!

I watched a YouTube video with how to take the dryer apart and remove the sensors. I followed the what the instructions were removing the top of the dryer and then the front panel. Once that was removed it was a matter of removing 7 more screws and the lint collector piece came off. Popped the sensor pieces out. Cleaned the inside of the dryer and reinstalled a total of 5 parts and dryer is working fine and the clothes are drying in the allotted time it use to take.

I tipped the right side of the washer up 9.5 inches using two 2x4s and I was able to remove and replace the old hose with the tools described.

You will need a helper. Dismantle the Dryer: Remove the screws that hold the top cover, front control panel, front door and front panel. Release the V-Belt under the drum. Remove the Drum. Removed and replace the 2 Front roller assemblies - these were completely worn. Replaced the 2 rear rollers (did not replace the rear roller axels as these were more difficult to remove and they were in good shape) and the V-Belt while I had the whole thing open. Use a shop vac and cleaned up the whole unit. It is so nice and quiet now.

Opened front of dryer - removed drum - replace all 4 rollers (2 had bad shafts) - replace drum with new belt - reassembled

I took the top off, I disattached the front and took the front top of dryer off, taking the front of dryer off, detached the belt and took the drum out, found the wheels took the plastic triangle off and took the wheels off and replaced wheels, then did everything in reverse and no more thumping. just remember to unplug unit before working on it. And also Part Select is a very good site and place to get parts, very fair priced and very professional.

Remove old one and replace. Just make sure it is all the way on and secure or you will have a huge mess on your hands.

Pull out dryer and unplug 220v. With phillips screwdriver, remove 3 screws from back of top and slide top panel back approx 2 inches and remove. Unplug 4 wire sets from rear of control panel. Remove 2 screws from back of control panel, carefully pull top edge and remove control panel. Remove 4 screws from top of front panel, as well as bottom 2 screws from inside dryer door. Disconnect door light wire near 10 o'clock. Pull top of front panel forward and lift off of tabs. Disconnect filter sensor wire under panel on the right. Remove 2 screws from each side of inner front panel and lift until tabs disengaged from side panels. Pull out bottom edge, carefully disengage inner front panel from drum and remove it. Try to turn roller wheels that are on the rear of the inner front panel. The wheel can get lint inside the wheel/axle and freeze. If one or both is stuck and won't turn easily, use a couple small flathead screwdrivers to carefully remove the plastic triangle retainer off of the roller assembly of the wheel that is stuck. You do not need to unbolt the axle from the panel. Wipe off the axle and inside of wheel with a clean, soft, lint-free cloth. If the wheel has a flat spot from being rubbed by the drum, you will need to replace it as I did or it will make a thumping sound after cleaned and put back together. Do NOT grease or oil the wheel/axle. This will lead to more lint collection and clogging/freezing. Reverse to put back together.

Unplugged the dryer from the wall. Removed the back bracket holding the top on. Then the top will slide back and lift off. Next I removed the screws holding the control panel. Removed the door. Removed all the screws holding the front cover on. Removed the lent shoot. Manually rotated the tumbler. Checked both rollers in the front. Found one with the flat spot in it. Removed and replaced it.

Did the repair entirely from the back.- 4 screws back cover comes off. Once you see the Bellows it is obvious what needs to come off and there are other videos on the net showing this. The main things I did differently were 1) Leaned the washer forward and placed 3 2x4 blocks of wood under each back leg. This allowed me to reach under the washer with one hand, and through the back with the other. You need both hands in there ! 2) Uninstalling is easy with just pliers. But on the way back in, I used a pair of Locking Pliers to keep the circular clamp squeezed as much as possible. That seemed the only way to get the bellows back in. Another option would be to switch to screw on Pipe clamps instead of the spring clamps.

The repair went well and your parts are easy to find. This is the second time I have used your services and both times have been great. Your parts are at great prices and your delivery is a lot faster that one would think.
Thank you