FH4G2CDYV2 (ABWEVUS) LG Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from FENTON, MI
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Washer would not drain.
I followed the video and it was quite simple. There was an extra sheet metal screw at the bottom of the front panel which kept it from coming free of the three tabs. On the two pump wite connectors I made a mental note that the black wires were on top. The repair also fixed the lack of water flow through the degeterent dispenser. I was afraid of putting the tub seal back in place as a pro struggled with it when it was new and under warranty. It really was no problem at all. Take some phone pics along the way boosted my confidence.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrell from HENDERSONVLLE, NC
- Parts Used:
- 5220FR2075L, 5220FR2006H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Both were dripping water .
Watched video on U-Tube , unplug power cord, turn off water, take top off washing machine, remove water hoses, unscrew parts, remove hoses with pliers, install replacement parts, put all back together. Does not leak any more !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from DENHAM SPGS, LA
- Parts Used:
- 5220FR2075L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Old cold water inlet was leaking , as it progressively got worse,it poured.
With my wife's help( 2 shoukder surgeries ), pulled it forward, unplugged power source, turned Both water supplies off.
Removed two phillip screws from each upper ( plastic) holder.
Bumped top from front( works really well if you can use both arms,and with rubber gloves on for traction, or go to harbor freight purchase a glass suction cup) .
I marked ( with a sharpie) the solenoids/hoses,and wires, ( facing front ,right to left,1,2,3.), removed plugs,loosened clamps and pushed them back,gave each hose a twist,and removed them.
Took two screws 5/16 from the back that hold the valve assembly in out.
Removed old valve assembly, put new in place, reverse procedure for assembly. Once all is hooked up,and water dried, I plugged in,turned water on watched for two cycles( you need not stand over it,if it leaks you will know it) to double check, installed top,and we pushed it back in place.
Very simple to do,these washing machines are so easy to work on.
Now we enjoy a dry laundry room,and you can to.
??
Removed two phillip screws from each upper ( plastic) holder.
Bumped top from front( works really well if you can use both arms,and with rubber gloves on for traction, or go to harbor freight purchase a glass suction cup) .
I marked ( with a sharpie) the solenoids/hoses,and wires, ( facing front ,right to left,1,2,3.), removed plugs,loosened clamps and pushed them back,gave each hose a twist,and removed them.
Took two screws 5/16 from the back that hold the valve assembly in out.
Removed old valve assembly, put new in place, reverse procedure for assembly. Once all is hooked up,and water dried, I plugged in,turned water on watched for two cycles( you need not stand over it,if it leaks you will know it) to double check, installed top,and we pushed it back in place.
Very simple to do,these washing machines are so easy to work on.
Now we enjoy a dry laundry room,and you can to.
??
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marc from JACKSONVILLE, FL
- Parts Used:
- EBR78898213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Selector was not working
1. Unplug washer . Slide off top after removing two screws on back
2. Remove soap dish
3. Remove 3 screws holding front panel
4. Remove 3 electrical connectors
5. Carefully pry lock tabs holding front panel on down
6. Pull front panel off to work table.
7. Remove 8 screws holding PCB
8. Replace PCB with new one.
If additional help needed check youtube for video
2. Remove soap dish
3. Remove 3 screws holding front panel
4. Remove 3 electrical connectors
5. Carefully pry lock tabs holding front panel on down
6. Pull front panel off to work table.
7. Remove 8 screws holding PCB
8. Replace PCB with new one.
If additional help needed check youtube for video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Manuel from MESILLA PARK, NM
- Parts Used:
- 5220FR2075L
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washer would not fill with water and a (I E) Code displayed on the screen.
I looked at the video that is on the partselect.com website. The person that I talked to from the website was very knowledgeable about the problem with my washer and he gave me the part number to type in the search box of the website. When I typed the part number in the search box the part showed up and the installation video showed up also. The video is an excellent video. It shows exactly how to do it. I also downloaded the operator manual from the website to look up what the error code meant.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rudy from SAN DIEGO, CA
- Parts Used:
- 5220FR2006H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Hot water inlet had leak, kept filling washer, when offw
When to utube typed in my problem, very easy fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Castle Rock, CO
- Parts Used:
- 4738ER1002A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The tub-to-pump hose was leaking.
I tipped the right side of the washer up 9.5 inches using two 2x4s and I was able to remove and replace the old hose with the tools described.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from SUGAR GROVE, OH
- Parts Used:
- MDS62058301
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
water & soap leaked into / on the tub bearings causing Bearing failure
pretty straight forward repair,lots & lots of parts to clean :-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- willard from RIVERSIDE, CA
- Parts Used:
- 4280EN4001C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Drum was making a very load grinding sound
I took the washer completely apart and ordered any parts that looked worn and put it back together. It’s working like new and will last for a few years
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Myles from Kingston, NH
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Drain water was not being fully pumped out, leaving foul water in the tub and wet clothes smelling like sewage.
I removed the top of the washer, pried the front control panel off (pull a couple of electrical connecters or just rest it on something), separated the tub sleeve from the front panel and then removed the front panel (two screws). To remove the pump - just remove a couple of hoses, two wires and slide it out of the clip below. Reverse the process to install. A little daunting if you haven't done something like this before, but easily do-able once you get past your fears. A service call would cost much more than the $60.00 it took to get the part to my front door. This worked out really great - my wash smells fresh once again and my wife has moved on to the next project on her honey-do list!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Pie Town, NM
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Pump stopped working
Followed the video instructions provided.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from DEMING, NM
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Error code "EO", Drain Pump not working
I followed the video on the PartSelect web site for this repair and it went just fine. I also replaced the drain hose while I had everything apart. Thank you PartSelect, same day shipping. Arrived within 3 day's and your video was spot on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from GRANTS PASS, OR
- Parts Used:
- 4681EA2001T, 4738ER2002A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
WASHER WOULD NOT EMPTY WATER DURING RINSE
I BROUGHT UP THE YOUTUBE REPAIR VIDEO AND FOLLOWED IT STEP BY STEP AND WORKED OUT GREAT THANKS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Travis from Marietta, GA
- Parts Used:
- 4738ER1002A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
A leak was created via puncture of metal part of bra that fell out.
Remove old one and replace. Just make sure it is all the way on and secure or you will have a huge mess on your hands.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from pearl river, NY
- Parts Used:
- 5220FR2006H
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The hot water inlet valve was leaking at the seal between the valve and cellinoid.
Some screws, some clamps. Easy and straight forward. unplug machine, turn off water, disconnect water hose, unscrew top of machine (2 philips head screws), disconnect clamp from valve (use a towel for remaining water), disconnect wire, unscrew from place holder, remove entire valve, work backwards from there.
Was this instruction helpful to you?
Thank you for voting!