F1254FD (ABWEEUS) LG Washer - Instructions

new pump was a little different ,but mounted properly. Tipped washer on its side, changed pump by working trough bottom and back access. It went pretty smoothly, works fine.

Replaced rotor assembly by removing the back panel off the washer. Removed center bolt to be able to take out roto assembly. Magnets made it a little resistant, but with a little wiggling came off fairly easily.

The problem ended up being the pump motor which discharges water from the washer. I figured out this was the problem after trying several things. I determined the motor was fine when it was empty. With the unit turned off, if you can rotate the tube with a quick spin and it lights up, probably this is OK. Then I tried to run it again and it went about 1/2 way through the cycle and stopped and started humming again. So I started emptying out the water, which I noticed was about 5 gallons which is way too much. so once empty, I took the pump off by turning unit on side. There are two hoses with hose clamps, and a few screws. Be careful to mark which wire plugs onto which side of the pump. One is brown and one is black. If you take the pump housing off, with the 3 screws, you should be able to pull the motor apart. Mine had water and scum from the wash in it, which was a dead give away that it was the problem.

1. Remove spring-loaded clamp assembly. 2. Partially pull out the large rubber gasket near the lock switch assembly to gain access to the lock switch assembly. 3. Unscrew two screws holding the lock switch assembly. Carefully separate the connector from the lock screw assembly and replace it with the new part. Reinstall in reverse sequence. Ensure that the electrical connector is fully seated unto the lock switch assembly and the connector latch is fully set against the lock switch body. Also make sure that the large rubber seal is fully seated around the door opening to prevent water leak. Restarted the washer and everything worked as before.

The machine was making a grinding noise instead of draining. I spoke with the LG rep on the 800 line and was told to call a repair man. The Parts select diagram helped me to identify the part I needed. It was clear enough that I was confident it was the right one. Three days and six screws later the machine was working fine.

Simply took hose off from inside machine and replaced it with new one. The tore one had a stopper on one end that wrapped to front machine; inside filter compartment. So I put stopper on the other end of new hose and wrapped it to it's holding spot in filter compartment.

found the leak, went to the website, called customer service, ordered the part... $24 later, problem solved. Great customer service and on-line support

The repair went well and your parts are easy to find. This is the second time I have used your services and both times have been great. Your parts are at great prices and your delivery is a lot faster that one would think.
Thank you

pulled off top of washer to get at the inlet valve disconnect two hoses take two screws out and then you put it back together the way you took apart and your done

Unplug Washing machine first. Then remove 2 screws at the back of the top cover. Slide the top cover back then lift and remove. Unplug electrical connector @ inlet valve and remove water lines 1 going in and 1 out of valve. Remove 2 screws holding assembly in place then install new valve assembly and all other components in reverse order.

removed top, removed 2 screws, replace part. did not fix problem, the real problem was the water inlet valve, works great, easy fix. thanks

Removed lid (top of washer), then ran a cycle in normal to identify the failed component, then noticed the water inlet valve assembly for the hot water was leaking, used my pc and went to website Part Select and found to failed part on the parts break down item, then ordered the part, the part "Valve Assembly Inlet" for the hot water arrived 2-days later, replaced valve in less than 5-minutes, disconnected push on electrical connector, unscrewed the valve assembly inlet and installed the new valve assembly inlet, very easy

Removed the old bellows (2 squeeze hose clamps and one screw adjustable hose clamp) slid on the new one and it was done!

The pump is apparently used for more than one washer, and the R&R instructions may be significantly different. I found a youtube video for my exact washer.

Removed the top, the front, got to the pump, removed it and replace it with the new one.