WM2377CW LG Washer - Instructions

Unplug Washing machine first. Then remove 2 screws at the back of the top cover. Slide the top cover back then lift and remove. Unplug electrical connector @ inlet valve and remove water lines 1 going in and 1 out of valve. Remove 2 screws holding assembly in place then install new valve assembly and all other components in reverse order.

I removed the top off the washer, unplugged from the electrical, removed the three hoses and wiring plugs, removed the two screws holding the valve assembly in place, and replaced the part with the new. It was a very simple swap, and I even found a video on YouTube on how to replace it.

Simply took hose off from inside machine and replaced it with new one. The tore one had a stopper on one end that wrapped to front machine; inside filter compartment. So I put stopper on the other end of new hose and wrapped it to it's holding spot in filter compartment.

found the leak, went to the website, called customer service, ordered the part... $24 later, problem solved. Great customer service and on-line support

The repair went well and your parts are easy to find. This is the second time I have used your services and both times have been great. Your parts are at great prices and your delivery is a lot faster that one would think.
Thank you

Unplugged the washer,removed the rear cover, removed the old rotor assembly & installed the new rotor with thread lock on the retaining bolt.

First we unplugged the machine. Then turned off the water and disconnected the hoses. Pulled out the machine and laid it on its side to access the themsistor located on the drum. (No, you do not have to remove the control panel at all to replace this part) The thermsistor is clearly seen with a flashlight. There were plastic ties holding the wires of the thermsistor so we used small scissors to cut the ties. Then unplugged the old thermsistor and plugged in the new thermsistor and used a regular bag twist to secure the wires. Repair complete and the machine is back to normal. Thank you Part Select.

After finding you on google it was easy to repair. It saved me $95.00 service charge. Your direction made it very easy.

removed top, removed 2 screws, replace part. did not fix problem, the real problem was the water inlet valve, works great, easy fix. thanks

Removed lid (top of washer), then ran a cycle in normal to identify the failed component, then noticed the water inlet valve assembly for the hot water was leaking, used my pc and went to website Part Select and found to failed part on the parts break down item, then ordered the part, the part "Valve Assembly Inlet" for the hot water arrived 2-days later, replaced valve in less than 5-minutes, disconnected push on electrical connector, unscrewed the valve assembly inlet and installed the new valve assembly inlet, very easy

pulled off top of washer to get at the inlet valve disconnect two hoses take two screws out and then you put it back together the way you took apart and your done

found a slow leak in one of the valve seat gaskets and decided to replace the entire valve (also did the hot inlet as well just in case). Unplugged unit, detached water hoses (replaced these as well), moved the washer out about 12" from the wall. With Phillips head removed the washer top. With pliers removed the hose clamps off the valve heading to the detergent dispenser (be sure to keep track of what hose goes to what nipple). Detached electric clip from each solenoid. Using Phillips head removed the valve. Use reverse order to install new valve. Ran the unit through a long cycle with the top off to ensure there were no leaks.

UNPLUG WASHER.Unscrew 4 screws holding silver plate at back of unit. Remove plate to expose inside of unit. Locate drain hose at bottom of washer tub. Hose connects at front drain, bottom of tub, and at rear at the pressure sensor. Front and rear simply slide clamps down by grasping clamp tabs and sliding clamp off connection point. Disconnect from tub bottom by loosening main clamp with Phillips screwdriver and pulling downward. Have a towel handy as there will be water in the hose, and it will pour out when removing it from the unit. Installation is the reverse of removal. ATTACH THE HOSE ASSEMBLY TO THE DRUM FIRST, THEN FRONT, THEN LASTLY REAR. This order is the easiest way, otherwise you will spend extra minutes trying to get the tub connection to seat properly. Plug it back in (duh), then you're good to go for another 4 years or so until another hole wears in the hose. I have performed this repair on 3 different units, with 4 years being the average lifespan of this part.

ordered part from Part Select and it was here very quickly,but the part came damaged (not the fault of Part Select). I ordered another one and PartSelect had it here the next day. I watched the video on how to replace it and it was very helpfull.The particular part I replaced (pump motor) does not seem very durable. I will buy an American made washer the next time I need one. I will use Partselect in the future and recomend it to others.

the best video was on you tube and showed exactly how to repair my washer. the parts arrived quickly and was a perfect match. thanks for helping me save some moola and making mama happy.