WM3070HVA LG Washer - Instructions

Simply took hose off from inside machine and replaced it with new one. The tore one had a stopper on one end that wrapped to front machine; inside filter compartment. So I put stopper on the other end of new hose and wrapped it to it's holding spot in filter compartment.

Super easy to find the part thanks to their diagrams. This fix was easy but I would definitely use this site again.

found the leak, went to the website, called customer service, ordered the part... $24 later, problem solved. Great customer service and on-line support

Unplug Washing machine first. Then remove 2 screws at the back of the top cover. Slide the top cover back then lift and remove. Unplug electrical connector @ inlet valve and remove water lines 1 going in and 1 out of valve. Remove 2 screws holding assembly in place then install new valve assembly and all other components in reverse order.

I removed the top off the washer, unplugged from the electrical, removed the three hoses and wiring plugs, removed the two screws holding the valve assembly in place, and replaced the part with the new. It was a very simple swap, and I even found a video on YouTube on how to replace it.

pulled off top of washer to get at the inlet valve disconnect two hoses take two screws out and then you put it back together the way you took apart and your done

The repair went well and your parts are easy to find. This is the second time I have used your services and both times have been great. Your parts are at great prices and your delivery is a lot faster that one would think.
Thank you

Turn off hot water supply and activate a cycle on the washer momentarily, with hot water selected on front panel options to relieve hose pressure. Slide washer out to gain access to rear of unit. Unplug washer from AC source. Using pliers, remove washer supply hose from washer-side of the line (water may drain from hose) Remove single Phillips screw at bottom of each nylon lid holder at rear. Using a plastic putty knife, place between front panel and top lid to loosen lid and slide to rear. Remove lid and store aside. Hot and cold inlet valves sit side-by-side at top rear of the unit. Disconnect connector from valve by pulling gently away from valve plug prongs and place to the side. Using pliers, compress hose clamp and move to lower section of hose. Carefully rotate hose back and forth to remove from assembly. Inlet valve is held to washer body rear with 3 small Phillips screws. Remove first 2 and then while holding inlet valve body, remove final screw to free inlet valve assembly. Replace with new assembly by reversing these steps.Make certain when supply hose is reconnected, it is firmly tightened but DO NOT over tighten. Test washer by running a cycle to ensure there are no leaks.

Took off the old one and put the other one on. The only difficulty was that my husband has big hands and had a hard time getting to one end.

new pump was a little different ,but mounted properly. Tipped washer on its side, changed pump by working trough bottom and back access. It went pretty smoothly, works fine.

I unplugged the washer, and removed the top of the washer by removing the two screws securing the top to the washer. You'll find them inside the two plastic pieces on the rear of the top. Remove only the bottom two screws in each plastic piece and slide the lid to the rear a few inches then lift straight up to remove the lid. Disconnect the water hose from the rear of the inlet valve assembly then remove the two screws in the rear of the old water valve bracket that attach it to the washer. Pull the old unit inside the washer and set the new unit on top of the old. Swap over the electrical connections to the new water valve assembly, matching the locations where the connectors were originally. Then swapped over the water lines from the old unit to the new unit using common pliers to compress the hose claps. Finally, attach the new unit to the washer with the two rear screws. Replace the water hose and the top, and the unit is ready to test.

1. Remove spring-loaded clamp assembly. 2. Partially pull out the large rubber gasket near the lock switch assembly to gain access to the lock switch assembly. 3. Unscrew two screws holding the lock switch assembly. Carefully separate the connector from the lock screw assembly and replace it with the new part. Reinstall in reverse sequence. Ensure that the electrical connector is fully seated unto the lock switch assembly and the connector latch is fully set against the lock switch body. Also make sure that the large rubber seal is fully seated around the door opening to prevent water leak. Restarted the washer and everything worked as before.

The machine was making a grinding noise instead of draining. I spoke with the LG rep on the 800 line and was told to call a repair man. The Parts select diagram helped me to identify the part I needed. It was clear enough that I was confident it was the right one. Three days and six screws later the machine was working fine.

Ordered a new water valve, easy installation, removed top cover of washer. Two screws and three hose clamps, done in 20 minutes.

removed 2 screws on back. removed top. disconected wires and hoses removes 2 screws holding assy in place and removed assy. put in new assy and installed hoses and plugs in same location removed from. reinstalled top and hose and ran washer.. new valve unite works but has a high pitched whine when valves turn on. :(