79641272211 LG Washer - Instructions

The machine was making a grinding noise instead of draining. I spoke with the LG rep on the 800 line and was told to call a repair man. The Parts select diagram helped me to identify the part I needed. It was clear enough that I was confident it was the right one. Three days and six screws later the machine was working fine.

This was very easy to instal. The aplaiance repair co. wanted $240 my LG is six years old and would rather buy a new one if I had to spend that much, so I gave it a shot and it took me 20 min to install the part. Told my wife she owed me $ 180 for my labor.

Unplug washer!!! 1. Remove retaining ring around rubber gasket with flat head screwdriver. Just slightly pry off and it will easily come off. 2. Just peel back rubber gasket on the side that the lock is on. 3. remove 2 screws from the front off the lock assembly. 4. gently reach in and lift the little plastic clip holding the wiring harness and lift straight off. If the clip is lifted it might be a little tight just use even steady pressure to pull off. 5. Reverse these instructions to replace. Note: replacing the retaining ring on the rubber is a pain. The spring has to be in the bottom. Using a couple of flathead screwdrivers you can wrangle it back in place after awhile. There is a tool that looks like a large reverse pliers that may make it easier. Anyway thats it, pretty easy. There is a youtube video that shows all of this.

took out the drain pump and replace with a new one

During my troubleshooting, I removed the bottom to access the drain pump. I had to cut some wire ties so that I could make removing the wires easier. After checking the pump and putting everything back together, I determined that the pump itself was bad. Pump impeller should not rotate freely! After receiving new part, I installed it relatively easy. I didn't have to remove the bottom since there was enough room through the access hole. Just make sure to make where wires go before removing old part.

new pump was a little different ,but mounted properly. Tipped washer on its side, changed pump by working trough bottom and back access. It went pretty smoothly, works fine.

Took off the old one and put the other one on. The only difficulty was that my husband has big hands and had a hard time getting to one end.

The pump is apparently used for more than one washer, and the R&R instructions may be significantly different. I found a youtube video for my exact washer.

Removed the top, the front, got to the pump, removed it and replace it with the new one.

Found the part of Part Select by describing the problem. used a Utube video and step by step we were able to take apart, replace and put back everything with just a screw driver - I saved so much money!

Found great Youtube video, followed step by step. Only difficult part was getting the tub gasket clamp back on. But all in all pretty easy. If tub won't drain and weird noise coming from pump do not hesitate to do it yourself and save some coin!

Found on line OE meant washer not pumping out water with the suggestion to clean the filter and inspect the pump and lines for blockage. No problems there. You must be careful to empty the water manually before removing the filter. My wet vac helped but I still made a mess. I found a mechanic to look at the washer. He said it is common for the pump on these washers to go bad, especially if the washer has sat out of service. They wanted $300 to replace the pump. I found the part on this website for $53 and replaced it myself. The only hard part was emptying the water without making a mess and leaning the washer up and back far enough safely to remove the pump, then working on my back under the machine.

My washer would try to spin and remove the water according to the time allowed. Consequently my washer would take longer than the time allowed to drain therefore water would send a code error then the machine would stop working. So I remove the hose from the pump and found my son's little small sock blocking the drain. I removed the sock and reinstalled all hoses. Everything is fine now. No need for a replacement item. Just a little servicing.

greate very easy and the parts fit awsome the shiping was fast and easy very satified

Contacted LG customer service, not much help there. Watched a very helpful Utube video on how to find and repair the leak. The video suggested that the most common leak is in the drain hose with bellows. Removed the rear panel and removed the bellows unit using pliers for the clamps and screwdriver for the bellows part. This was pretty easy. The rubber bellows was leaking in the exact same place as the youtube video showed. This is a Design Flaw that LG needs to fix. Ordered the new part and installed the bellows portion of the part first, as the angle for that installation needs to be correct. Then attempted to install the end of the hose (very inaccesible) to the pump drain. Very difficult to position the factory supplied spring clamp with pliers so I purchased a screw-type clamp (using the nut-driver rather than a screw-driver to tighten the clamp was helpful) at the local hardware store and that made my job much easier. Note: My unit is mounted on a pedestal, so it was a little easier to access the part location (about one foot off the floor, rather than at floor level), but it may be that the part should be replaced from the bottom of the unit, which would make it much easier to access. Then I installed the other end of the hose to the drain line using a screw-type clamp. I am 69 years old, and not that flexible anymore, so getting down on the floor to reach inside the unit was difficult. You need patience to do this job and you have to make sure all the clamps are properly installed so you don't start the machine up and end up with another leak. For me, this process was difficult and took more than two hours to complete. Limited access to the area made it more difficult and I hate the factory clamps they use. Overall, the repair costs about $25, compared to the $125 just to come look at the machine, then more money to fix the unit. It was satisfying to complete the repair for a small amount of money, but not sure it was worth the aggravation.