79641722000 LG Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Scott from Winston-Salem, NC
- Parts Used:
- 5220FR2008H, 5220FR2006H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Water dripping into tub when washer not in use.
Was very easy. Unplug and disconnect the water lines. Removed 2 screws and popped off the top of the washer. Removed the power connectors and the hoses. Unscrewed 2 more screws and dropped out the old inlet valves. Put in the new inlet valves, screwed them in, reconnected the hoses and power connectors. Replaced the lid, reconnected the water lines and put the top back on. Done. So easy! No more drip!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chris from glenwood springs, CO
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
my lg washer wasnt draining
It was so easy. i searched my model it brought up this site and the most common problem popped up without my even asking and recommended the part. i got it one week later and it was so simple to fix. a repair man wanted three times the part price to come to my home twice and would have had to wait longer. you guys were very helpful
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- nicole from chicago, IL
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
water would not drain, nothing jamming pump
new pump was a little different ,but mounted properly. Tipped washer on its side, changed pump by working trough bottom and back access. It went pretty smoothly, works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Show Low, AZ
- Parts Used:
- 4738ER1002A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
It was torn and leaking.
Took off the old one and put the other one on. The only difficulty was that my husband has big hands and had a hard time getting to one end.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juan from Anaheim, CA
- Parts Used:
- EBF49827801
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Will not start after dorr is closed. Shows Code dE. Door locks properly, two clicking is heard before code shows up.
1. Remove spring-loaded clamp assembly. 2. Partially pull out the large rubber gasket near the lock switch assembly to gain access to the lock switch assembly. 3. Unscrew two screws holding the lock switch assembly. Carefully separate the connector from the lock screw assembly and replace it with the new part. Reinstall in reverse sequence. Ensure that the electrical connector is fully seated unto the lock switch assembly and the connector latch is fully set against the lock switch body. Also make sure that the large rubber seal is fully seated around the door opening to prevent water leak. Restarted the washer and everything worked as before.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- matt from Fuquay Varina, NC
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My Washing Machine was not draining properly
The machine was making a grinding noise instead of draining. I spoke with the LG rep on the 800 line and was told to call a repair man. The Parts select diagram helped me to identify the part I needed. It was clear enough that I was confident it was the right one. Three days and six screws later the machine was working fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Damascus, MD
- Parts Used:
- 6201EC1006T
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washer will not power on
Disconnected power. Removed washer top; only 2 screws in back. Disconnected two wire connectors on Filter Assembly Circuit. Removed assembly; 1 screw. Installed new assembly, reconnected wires, and replaced washer top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from West Hills, CA
- Parts Used:
- 4738ER1002A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
My Washer was leaking
The repair went well and your parts are easy to find. This is the second time I have used your services and both times have been great. Your parts are at great prices and your delivery is a lot faster that one would think.
Thank you
Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerald from wis dells, WI
- Parts Used:
- 5220FR2006H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
the water inlet was leaking
pulled off top of washer to get at the inlet valve disconnect two hoses take two screws out and then you put it back together the way you took apart and your done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tresa from McHenry, IL
- Parts Used:
- 5214FR4006G
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Very visible tear in hose. It was 1 1/2" long
Simply took hose off from inside machine and replaced it with new one. The tore one had a stopper on one end that wrapped to front machine; inside filter compartment. So I put stopper on the other end of new hose and wrapped it to it's holding spot in filter compartment.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JACK from Kingston, WA
- Parts Used:
- AGM73610701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Magnetic door plunger broke
Super easy to find the part thanks to their diagrams. This fix was easy but I would definitely use this site again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Granite Bay, CA
- Parts Used:
- 5220FR2006H, 4861FR3068A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
leaky inlet valve
found the leak, went to the website, called customer service, ordered the part... $24 later, problem solved. Great customer service and on-line support
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sherman from BROKEN ARROW, OK
- Parts Used:
- 6601ER1006E
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
h2o filled w/o stopping
removed top, removed 2 screws, replace part. did not fix problem, the real problem was the water inlet valve, works great, easy fix. thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARVIN from MARYVILLE, TN
- Parts Used:
- 5220FR2006H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Hot Water Inlet valve (solinoid valve leaking)
Removed lid (top of washer), then ran a cycle in normal to identify the failed component, then noticed the water inlet valve assembly for the hot water was leaking, used my pc and went to website Part Select and found to failed part on the parts break down item, then ordered the part, the part "Valve Assembly Inlet" for the hot water arrived 2-days later, replaced valve in less than 5-minutes, disconnected push on electrical connector, unscrewed the valve assembly inlet and installed the new valve assembly inlet, very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Commack, NY
- Parts Used:
- 5220FR2006H
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Leaking Hot Water Intake Valve
I received the part needed within a few days from ordering. I immediately removed the leaking part with the new part. It was a very simple install, and my washer is now leak free. If you think you cannot do these simple changes, think again, it's much easier then you may think. Remove the top cover of your washer machine by taking off the two screws in the back. Remove the hose clamp with a pair of pliers and pull off from the intake valve, of course make sure your water valve is shut off before starting. Remove the two prong clip. Using your pliers, disconnect the main hot water hose. Use a Phillips screwdriver to remove the two screws that holds the valve in place. Remove and discard it and replace with the new valve. Follow the steps and your done, it's that easy....TC
Was this instruction helpful to you?
Thank you for voting!