GCWP1069CD1 (ABWEELC) LG Washer - Instructions

removed dryer which was stacked on top of dryer. opened washer top by removing screws from plastic hold down parts on rear. replaced valves with new valves you all sent me. reassembled and restacked dryer on washer

I received the part needed within a few days from ordering. I immediately removed the leaking part with the new part. It was a very simple install, and my washer is now leak free. If you think you cannot do these simple changes, think again, it's much easier then you may think. Remove the top cover of your washer machine by taking off the two screws in the back. Remove the hose clamp with a pair of pliers and pull off from the intake valve, of course make sure your water valve is shut off before starting. Remove the two prong clip. Using your pliers, disconnect the main hot water hose. Use a Phillips screwdriver to remove the two screws that holds the valve in place. Remove and discard it and replace with the new valve. Follow the steps and your done, it's that easy....TC

I ran the spin & drain cycle to empty the drum,I waited to be see how long it took to see a noticeable level of water in the drum (1-2hrs).decided to check the cold water valve first.Found that there was rust forming around the solnoid piston,making it hang up,most of the time it tryed to open, or close. cleaned with light sand paper(piston), and ordered part with parts select. Which was real easy,because of the knowledgeable staff,parts came in as promised,and in good shape,and most important of all it was the exact replacement part. My wife is HAPPY,which makes my life good too! THANKS Parts select..

I took the back panel off the washer and located where the leak was coming from. It was obviously coming from around where the cold water hose connects. Checked washers in hoses and they were good. Noticed a small drip on the valve assembly that the hose connects too. Took off small panel where the hose connections are mounted....disconnected all 3 black water hoses that connect to it (squeeze metal clamps with pliers and slide hoses off. and numbered them with permanent marker so I wouldn't get my lines crossed later), removed the quick disconnect electrical lines.... removed part and googled the parts diagram on this site.....identified the part in the pic and ordered....it was here in less than 48 hrs with the basic shipping (which stated 3-5 days:)....reassembled the same way I took it apart. I'm prud of myself, it was pretty easy and I'm sure it saved me a lot of money!:)l

Followed the instructions that a fellow DIYer posted in PartSelect and a few I watched on Youtube. Pull out the detergent drawer, remove the back screws, slide the top off, unclip the control board, unplug Power & One more switch so that I could move it aside. Take the gasket retention wire off the door gasket & tuck it inside. Remove the screws in the bottom & top. Then slide the front panel, including the door up (not easy) and out. The part received was only the pump motor so I had to take a few pictures before so I knew I got it together right. Remove drain houses, pump screws, slide pump back and remove pump. A few more screws to remove the pump from the housing & replace with new pump. Put it all back together. It works! It only took about 45 minutes

UNPLUG WASHER.Unscrew 4 screws holding silver plate at back of unit. Remove plate to expose inside of unit. Locate drain hose at bottom of washer tub. Hose connects at front drain, bottom of tub, and at rear at the pressure sensor. Front and rear simply slide clamps down by grasping clamp tabs and sliding clamp off connection point. Disconnect from tub bottom by loosening main clamp with Phillips screwdriver and pulling downward. Have a towel handy as there will be water in the hose, and it will pour out when removing it from the unit. Installation is the reverse of removal. ATTACH THE HOSE ASSEMBLY TO THE DRUM FIRST, THEN FRONT, THEN LASTLY REAR. This order is the easiest way, otherwise you will spend extra minutes trying to get the tub connection to seat properly. Plug it back in (duh), then you're good to go for another 4 years or so until another hole wears in the hose. I have performed this repair on 3 different units, with 4 years being the average lifespan of this part.

Tipped the washer on its side to expose the bottom, removed the plastic lid adjacent to the pump after removing the screws holding it , then, using a flat head on a pry tab pulled out the pump, removed the hoses with pliers to complete the extraction, swapped the pump on my bench. . assembly is reverse of disassembly. .

ordered part from Part Select and it was here very quickly,but the part came damaged (not the fault of Part Select). I ordered another one and PartSelect had it here the next day. I watched the video on how to replace it and it was very helpfull.The particular part I replaced (pump motor) does not seem very durable. I will buy an American made washer the next time I need one. I will use Partselect in the future and recomend it to others.

found a slow leak in one of the valve seat gaskets and decided to replace the entire valve (also did the hot inlet as well just in case). Unplugged unit, detached water hoses (replaced these as well), moved the washer out about 12" from the wall. With Phillips head removed the washer top. With pliers removed the hose clamps off the valve heading to the detergent dispenser (be sure to keep track of what hose goes to what nipple). Detached electric clip from each solenoid. Using Phillips head removed the valve. Use reverse order to install new valve. Ran the unit through a long cycle with the top off to ensure there were no leaks.

We drained the water from the washer via the tiny hose/filter located at the lower left corner of the washing machine. The unit was then pulled away from the wall, unplugged and the hoses disconnected. At this time, we used the wet dry vacuum to suction the water that remained in the drain hose. We tilted the washing machine back until the front of the unit was 18 inches or so off the floor. We used the foot stool to hold the washer up in the air so that we could work on the pump. Replacing the pump was as easy as removing a few screws, unplugging the electrical connections and removing the faulty pump assembly from the plastic housing. (Be sure to mark what connector goes in what terminal). Re-assemble. Re-connect. You are ready to go. It took more time to ready the washer than it did to replace the part.

First, slide top cover back, then lift of washer. Remember to turn off water supply and disconnect cold water hose before working on valve. Also, unplug washer from wall socket. Disconnect three small electric plugs from valve, noting the postion on valve,then disconnect the water hoses from valve, noting postition of each hose. Remove two small screws holding valve to washer,remove and replace valve.reistall valve, reconnect hoses and electric connectors. Reconnect water supply, turn on water supply, check for leak, reconnect power cord to wall socket. Run washer through normal wash cycle, observing water valve for leaks, normal operation, if no problems, then reinstall top on washer

Unplugged the washer,removed the rear cover, removed the old rotor assembly & installed the new rotor with thread lock on the retaining bolt.

The repair went well and your parts are easy to find. This is the second time I have used your services and both times have been great. Your parts are at great prices and your delivery is a lot faster that one would think.
Thank you

pulled off top of washer to get at the inlet valve disconnect two hoses take two screws out and then you put it back together the way you took apart and your done

Unplug Washing machine first. Then remove 2 screws at the back of the top cover. Slide the top cover back then lift and remove. Unplug electrical connector @ inlet valve and remove water lines 1 going in and 1 out of valve. Remove 2 screws holding assembly in place then install new valve assembly and all other components in reverse order.