All Installation Instructions for LG Washer GCWL1069CS1

Customer:: Howard from Aubrey, TX
Parts Used:: 5221ER1003A
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Inlet cold water valve leaking

Ordered a new water valve, easy installation, removed top cover of washer. Two screws and three hose clamps, done in 20 minutes.

Was this instruction helpful to you?

Customer:: Creed from Surprise, AZ
Parts Used:: 5221ER1003A
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

leaking from solenoid

removed 2 screws on back. removed top. disconected wires and hoses removes 2 screws holding assy in place and removed assy. put in new assy and installed hoses and plugs in same location removed from. reinstalled top and hose and ran washer.. new valve unite works but has a high pitched whine when valves turn on. :(

Was this instruction helpful to you?

Customer:: James from Roper, NC
Parts Used:: 5221ER1003A, 5220FR2006H
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Replace inlet water valve assemblies

Our washer and dryer was stacked, and had to remove the dryer to access top of washer. This took 2 people and was not difficult due to the 168 lb weight of the dryer. Turned of water, pulled washer away from wall and disconnected the supply hoses. Removed the 2 screws holding the top, slipped it back and removed. Removed the 2 screws holding the inlet valve assembly, unplugged the wiring harness from the 3 solenoids, disconnected the 3 hoses from the hose bibs on the valves. Mounted new valve assembly, connected hoses making sure that clamps did not touch any other hoses, reconnected wiring harness, turned on water to check for any leaks, put top back on and tried washer out. Changing the valve assembly took a total of 15 minutes. Really simple. The You tube video very helpful in determining how to do the job.

Was this instruction helpful to you?

Customer:: nicole from chicago, IL
Parts Used:: 4681EA2001T
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

water would not drain, nothing jamming pump

new pump was a little different ,but mounted properly. Tipped washer on its side, changed pump by working trough bottom and back access. It went pretty smoothly, works fine.

Was this instruction helpful to you?

Customer:: Verle from Malcolm, NE
Parts Used:: 4738ER1002A
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers

Bellows had developed a small hole

Removed the old bellows (2 squeeze hose clamps and one screw adjustable hose clamp) slid on the new one and it was done!

Was this instruction helpful to you?

Customer:: Denise from Show Low, AZ
Parts Used:: 4738ER1002A
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers, Wrench (Adjustable)

It was torn and leaking.

Took off the old one and put the other one on. The only difficulty was that my husband has big hands and had a hard time getting to one end.

Was this instruction helpful to you?

Customer:: Daraius from AUSTIN, TX
Parts Used:: 4738ER1002A
Difficulty Level:: A Bit Difficult
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Screw drivers

Pool of water under washer after a run

Did the repair entirely from the back.- 4 screws back cover comes off. Once you see the Bellows it is obvious what needs to come off and there are other videos on the net showing this. The main things I did differently were 1) Leaned the washer forward and placed 3 2x4 blocks of wood under each back leg. This allowed me to reach under the washer with one hand, and through the back with the other. You need both hands in there ! 2) Uninstalling is easy with just pliers. But on the way back in, I used a pair of Locking Pliers to keep the circular clamp squeezed as much as possible. That seemed the only way to get the bellows back in. Another option would be to switch to screw on Pipe clamps instead of the spring clamps.

Was this instruction helpful to you?

Customer:: william from Mobile, AL
Parts Used:: AHL72914402
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

The bolt on the motor rotor loosened allowing the motor shaft to wallow out the plastic bushing in the rotor.

Unplugged the washer,removed the rear cover, removed the old rotor assembly & installed the new rotor with thread lock on the retaining bolt.

Was this instruction helpful to you?

Customer:: Bruce from West Hills, CA
Parts Used:: 4738ER1002A
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Pliers

My Washer was leaking

The repair went well and your parts are easy to find. This is the second time I have used your services and both times have been great. Your parts are at great prices and your delivery is a lot faster that one would think.
Thank you

Was this instruction helpful to you?

Customer:: gerald from wis dells, WI
Parts Used:: 5220FR2006H
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

the water inlet was leaking

pulled off top of washer to get at the inlet valve disconnect two hoses take two screws out and then you put it back together the way you took apart and your done

Was this instruction helpful to you?

Customer:: Robert from Asheville, NC
Parts Used:: 5220FR2006H
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

Water inlet valve coil was leaking water.

Unplug Washing machine first. Then remove 2 screws at the back of the top cover. Slide the top cover back then lift and remove. Unplug electrical connector @ inlet valve and remove water lines 1 going in and 1 out of valve. Remove 2 screws holding assembly in place then install new valve assembly and all other components in reverse order.

Was this instruction helpful to you?

Customer:: Drew from Thomaston, GA
Parts Used:: 5221ER1003A
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

I had a slow leak coming from the factory cold inlet water valve assembly, and removed the top and found it rusted.

I removed the top off the washer, unplugged from the electrical, removed the three hoses and wiring plugs, removed the two screws holding the valve assembly in place, and replaced the part with the new. It was a very simple swap, and I even found a video on YouTube on how to replace it.

Was this instruction helpful to you?

Customer:: Tresa from McHenry, IL
Parts Used:: 5214FR4006G
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Very visible tear in hose. It was 1 1/2" long

Simply took hose off from inside machine and replaced it with new one. The tore one had a stopper on one end that wrapped to front machine; inside filter compartment. So I put stopper on the other end of new hose and wrapped it to it's holding spot in filter compartment.

Was this instruction helpful to you?

Customer:: JACK from Kingston, WA
Parts Used:: AGM73610701
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Magnetic door plunger broke

Super easy to find the part thanks to their diagrams. This fix was easy but I would definitely use this site again.

Was this instruction helpful to you?

Customer:: Michael from Granite Bay, CA
Parts Used:: 5220FR2006H, 4861FR3068A
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

leaky inlet valve

found the leak, went to the website, called customer service, ordered the part... $24 later, problem solved. Great customer service and on-line support

Was this instruction helpful to you?

GCWL1069CS1 (ABWEELC) LG Washer - Instructions