Models > GCWP1069CD2 > Instructions

GCWP1069CD2 (ASSEELC) LG Washer - Instructions

Jump to:

All Instructions for the GCWP1069CD2

Customer:: Thomas from Salisbury, NC
Parts Used:: 5221ER1003A, 5220FR2006H
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Screw drivers, Wrench (Adjustable)

found a leak in the cold water inlet valve- one of the seat gaskets was bad

found a slow leak in one of the valve seat gaskets and decided to replace the entire valve (also did the hot inlet as well just in case). Unplugged unit, detached water hoses (replaced these as well), moved the washer out about 12" from the wall. With Phillips head removed the washer top. With pliers removed the hose clamps off the valve heading to the detergent dispenser (be sure to keep track of what hose goes to what nipple). Detached electric clip from each solenoid. Using Phillips head removed the valve. Use reverse order to install new valve. Ran the unit through a long cycle with the top off to ensure there were no leaks.

Was this instruction helpful to you?

Customer:: PAMELA from DE SOTO, MO
Parts Used:: 4681EA2001T
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Nutdriver, Screw drivers

The drain pump impeller broke away from the pump.

We drained the water from the washer via the tiny hose/filter located at the lower left corner of the washing machine. The unit was then pulled away from the wall, unplugged and the hoses disconnected. At this time, we used the wet dry vacuum to suction the water that remained in the drain hose. We tilted the washing machine back until the front of the unit was 18 inches or so off the floor. We used the foot stool to hold the washer up in the air so that we could work on the pump. Replacing the pump was as easy as removing a few screws, unplugging the electrical connections and removing the faulty pump assembly from the plastic housing. (Be sure to mark what connector goes in what terminal). Re-assemble. Re-connect. You are ready to go. It took more time to ready the washer than it did to replace the part.

Was this instruction helpful to you?

Customer:: william from Mobile, AL
Parts Used:: AHL72914402
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

The bolt on the motor rotor loosened allowing the motor shaft to wallow out the plastic bushing in the rotor.

Unplugged the washer,removed the rear cover, removed the old rotor assembly & installed the new rotor with thread lock on the retaining bolt.

Was this instruction helpful to you?

Customer:: William from Campbellsville, KY
Parts Used:: 5221ER1003A
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

Leaking water on my Hardwood floor

After finding you on google it was easy to repair. It saved me $95.00 service charge. Your direction made it very easy.

Was this instruction helpful to you?

Customer:: Bruce from West Hills, CA
Parts Used:: 4738ER1002A
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Pliers

My Washer was leaking

The repair went well and your parts are easy to find. This is the second time I have used your services and both times have been great. Your parts are at great prices and your delivery is a lot faster that one would think.
Thank you

Was this instruction helpful to you?

Customer:: Robert from Asheville, NC
Parts Used:: 5220FR2006H
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

Water inlet valve coil was leaking water.

Unplug Washing machine first. Then remove 2 screws at the back of the top cover. Slide the top cover back then lift and remove. Unplug electrical connector @ inlet valve and remove water lines 1 going in and 1 out of valve. Remove 2 screws holding assembly in place then install new valve assembly and all other components in reverse order.

Was this instruction helpful to you?

Customer:: gerald from wis dells, WI
Parts Used:: 5220FR2006H
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

the water inlet was leaking

pulled off top of washer to get at the inlet valve disconnect two hoses take two screws out and then you put it back together the way you took apart and your done

Was this instruction helpful to you?

Customer:: Tresa from McHenry, IL
Parts Used:: 5214FR4006G
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Very visible tear in hose. It was 1 1/2" long

Simply took hose off from inside machine and replaced it with new one. The tore one had a stopper on one end that wrapped to front machine; inside filter compartment. So I put stopper on the other end of new hose and wrapped it to it's holding spot in filter compartment.

Was this instruction helpful to you?

Customer:: JACK from Kingston, WA
Parts Used:: AGM73610701
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Magnetic door plunger broke

Super easy to find the part thanks to their diagrams. This fix was easy but I would definitely use this site again.

Was this instruction helpful to you?

Customer:: Michael from Granite Bay, CA
Parts Used:: 5220FR2006H, 4861FR3068A
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

leaky inlet valve

found the leak, went to the website, called customer service, ordered the part... $24 later, problem solved. Great customer service and on-line support

Was this instruction helpful to you?

Customer:: Drew from Thomaston, GA
Parts Used:: 5221ER1003A
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

I had a slow leak coming from the factory cold inlet water valve assembly, and removed the top and found it rusted.

I removed the top off the washer, unplugged from the electrical, removed the three hoses and wiring plugs, removed the two screws holding the valve assembly in place, and replaced the part with the new. It was a very simple swap, and I even found a video on YouTube on how to replace it.

Was this instruction helpful to you?

Customer:: sherman from BROKEN ARROW, OK
Parts Used:: 6601ER1006E
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

h2o filled w/o stopping

removed top, removed 2 screws, replace part. did not fix problem, the real problem was the water inlet valve, works great, easy fix. thanks

Was this instruction helpful to you?

Customer:: MARVIN from MARYVILLE, TN
Parts Used:: 5220FR2006H
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Hot Water Inlet valve (solinoid valve leaking)

Removed lid (top of washer), then ran a cycle in normal to identify the failed component, then noticed the water inlet valve assembly for the hot water was leaking, used my pc and went to website Part Select and found to failed part on the parts break down item, then ordered the part, the part "Valve Assembly Inlet" for the hot water arrived 2-days later, replaced valve in less than 5-minutes, disconnected push on electrical connector, unscrewed the valve assembly inlet and installed the new valve assembly inlet, very easy

Was this instruction helpful to you?

Customer:: Nate-Talisha from Miramar, FL
Parts Used:: 4681EA2001T
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Socket set

Water will not Drain

took out the drain pump and replace with a new one

Was this instruction helpful to you?

Customer:: Chris from Walla Walla, WA
Parts Used:: 4681EA2001T
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Water was not draining and was making a grinding noise

This was very easy to instal. The aplaiance repair co. wanted $240 my LG is six years old and would rather buy a new one if I had to spend that much, so I gave it a shot and it took me 20 min to install the part. Told my wife she owed me $ 180 for my labor.

Was this instruction helpful to you?

All Instructions for the GCWP1069CD2