31553 (ASTETEU) LG Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Paul from NANTICOKE, PA
- Parts Used:
- AGZ72909701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set, Wrench (Adjustable)
Washer was noisy, made noise when agitating and spinning.
I had a hard time removing the agitator, had to get thin prybar to get a hold of washplate. After I removed washplate, I found that the shaft that the washplate attaches to was actually worn out. What used to be a spline was smooth. So I ordered a new clutch assembly. There are a lot of bolts that hold the clutch assembly on to the basket. There are a lot of videos on Utube that will walk you through step by step. The only problem I encountered with this was removing the nut that holds the basket to the tub. One video said it was reverse thread, which it wasn’t. You can check the thread on new clutch assembly to see which way is correct. After I put back together. Works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas m from CARMICHAEL, CA
- Parts Used:
- 4263FA3933C
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
leg broke off inside housing
raised the front of washer by hand (literally) and placed two 2x4 blocks under front lip for support. reached up inside washer cabinet and unscrewed the broken leg piece upwards into the cabinet. this was the only way I could get the broken piece out without some specialized tool to reach it from the underside. replacement with the new leg was a breeze.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Lakeside, CA
- Parts Used:
- AJU75152601
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Cold water valve leaking.
turn off the water, unplug washer from power. remove two screws holding rear top plate. Here's the hard part. Pry the rear top plate from the top of the washer. It has multiple snap in guides across the front edge and they are very tight. Be careful and apply steady pressure straight up and they will eventually come free.
I marked each of the electrical inputs going to the old valve before removing. Remove the wiring harness. Again be careful and ease them off. the connectors
come apart easily. Remove the hose clamps with pliers and slip off the hoses. They are long enough that I trimmed off the soft ends of the old hoses and still had plenty of hose to reconnect. Remove the filler hoses. Remove the screws holding the valve to the machine. Re install the new valve in reverse order. Goes back in very easily.
Make sure to secure all the hoses. Run a wash cycle with an empty tub to make sure everything is working properly and nothing is leaking. Snap the rear top plate back into position and secure with the two screws Should take less than a couple of hours to do this job. Again the hardest part is getting the rear top plate off.
I marked each of the electrical inputs going to the old valve before removing. Remove the wiring harness. Again be careful and ease them off. the connectors
come apart easily. Remove the hose clamps with pliers and slip off the hoses. They are long enough that I trimmed off the soft ends of the old hoses and still had plenty of hose to reconnect. Remove the filler hoses. Remove the screws holding the valve to the machine. Re install the new valve in reverse order. Goes back in very easily.
Make sure to secure all the hoses. Run a wash cycle with an empty tub to make sure everything is working properly and nothing is leaking. Snap the rear top plate back into position and secure with the two screws Should take less than a couple of hours to do this job. Again the hardest part is getting the rear top plate off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from DICKSON CITY, PA
- Parts Used:
- 6323EL2001G
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washing machine was displaying te code. Quick google search to diagnose the issue.
Very simple repair after watching YouTube video on how to complete repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Crystal Lake, IL
- Parts Used:
- AJU75152601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
During the spin cycle water continued to flow into the machine.
unplugged machine, turned off water valves. Moved machine away from the wall. Disconnected supply lines. Removed cover housing water valve assembly.
Took a picture with phone. Disconnected water and electrical wires. Removed water valve assembly . Installed new assembly ,cover and reconnected supply lines, plugged power cord in, turned on water supply valves. Done.
Took a picture with phone. Disconnected water and electrical wires. Removed water valve assembly . Installed new assembly ,cover and reconnected supply lines, plugged power cord in, turned on water supply valves. Done.
Was this instruction helpful to you?
Thank you for voting!