Models > WM2250CW > Instructions

WM2250CW (ABWEPUS) LG Washer - Instructions

Jump to:

All Instructions for the WM2250CW
121 - 135 of 211
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Juan from Anaheim, CA
Parts Used:
EBF49827801
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Will not start after dorr is closed. Shows Code dE. Door locks properly, two clicking is heard before code shows up.
1. Remove spring-loaded clamp assembly. 2. Partially pull out the large rubber gasket near the lock switch assembly to gain access to the lock switch assembly. 3. Unscrew two screws holding the lock switch assembly. Carefully separate the connector from the lock screw assembly and replace it with the new part. Reinstall in reverse sequence. Ensure that the electrical connector is fully seated unto the lock switch assembly and the connector latch is fully set against the lock switch body. Also make sure that the large rubber seal is fully seated around the door opening to prevent water leak. Restarted the washer and everything worked as before.
Was this instruction helpful to you?
Thank you for voting!
Customer:
matt from Fuquay Varina, NC
Parts Used:
4681EA2001T
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
My Washing Machine was not draining properly
The machine was making a grinding noise instead of draining. I spoke with the LG rep on the 800 line and was told to call a repair man. The Parts select diagram helped me to identify the part I needed. It was clear enough that I was confident it was the right one. Three days and six screws later the machine was working fine.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Howard from Aubrey, TX
Parts Used:
5221ER1003A
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Inlet cold water valve leaking
Ordered a new water valve, easy installation, removed top cover of washer. Two screws and three hose clamps, done in 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Creed from Surprise, AZ
Parts Used:
5221ER1003A
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
leaking from solenoid
removed 2 screws on back. removed top. disconected wires and hoses removes 2 screws holding assy in place and removed assy. put in new assy and installed hoses and plugs in same location removed from. reinstalled top and hose and ran washer.. new valve unite works but has a high pitched whine when valves turn on. :(
Was this instruction helpful to you?
Thank you for voting!
Customer:
Verle from Malcolm, NE
Parts Used:
4738ER1002A
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Bellows had developed a small hole
Removed the old bellows (2 squeeze hose clamps and one screw adjustable hose clamp) slid on the new one and it was done!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Denise from Show Low, AZ
Parts Used:
4738ER1002A
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)
It was torn and leaking.
Took off the old one and put the other one on. The only difficulty was that my husband has big hands and had a hard time getting to one end.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Roper, NC
Parts Used:
5221ER1003A, 5220FR2006H
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Replace inlet water valve assemblies
Our washer and dryer was stacked, and had to remove the dryer to access top of washer. This took 2 people and was not difficult due to the 168 lb weight of the dryer. Turned of water, pulled washer away from wall and disconnected the supply hoses. Removed the 2 screws holding the top, slipped it back and removed. Removed the 2 screws holding the inlet valve assembly, unplugged the wiring harness from the 3 solenoids, disconnected the 3 hoses from the hose bibs on the valves. Mounted new valve assembly, connected hoses making sure that clamps did not touch any other hoses, reconnected wiring harness, turned on water to check for any leaks, put top back on and tried washer out. Changing the valve assembly took a total of 15 minutes. Really simple. The You tube video very helpful in determining how to do the job.
Was this instruction helpful to you?
Thank you for voting!
Customer:
nicole from chicago, IL
Parts Used:
4681EA2001T
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
water would not drain, nothing jamming pump
new pump was a little different ,but mounted properly. Tipped washer on its side, changed pump by working trough bottom and back access. It went pretty smoothly, works fine.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gregory from Collierville, TN
Parts Used:
5221ER1003A, 5220FR2006H
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
the hot and cold inlet valve assemblies were corroded and leaking out of the top
First I turned off the hot and cold water supply and removed the water lines from the back of the machine. I then unscrewed the 2 phillips head screws on the back of the washer for the cover. I slid the cover back and lifted it off the machine. Next, I unscrewed the mounting screws from each inlet valve assemble located on the back of the machine by the hose connections. I used pliers to pull the hose clamps back from the inlet valve, 1 at a time, then reconnected each hose and clamp on the new inlet valve. Once each hose was connected to the new inlet valve, I discarded the old inlet valves. I then re-attached each inlet valve. I placed the cover back on the machine and secured with the 2 screws, re-attached the water supply hoses to the hot and cold side and turned the hot and cold water supply back on. Everything successful, no leaks, and washing laundry again..........leak free!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Patrick from Ronkonkoma, NY
Parts Used:
4681EA2001T
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Not pumping out water
Hardest part was getting the correct part. Due to some glitch somewhere there was a mix up in the database for the correct pump number. This unit has two pumps mounted to the same housing. One is a recirculating pump and one is discharge pump. I ordered the discharge pump and kept receiving the recirculating pump. Discharge pump is LG PART#4681EA2001T and recirculating pump is LG PART #4681EA2002H Once in hand the install went fairly smoothly. Removed top - two screws on back of unit. Removed control panel with one screw on upper right inside corner, associated plugs and snap clips. Removed soap tray and drained water through filter tube. Removed screws in front of filter. Using Vise grips stretched spring from around front seal. Removed screws holding front of washer to top frame (2?)[accessed after soap tray removal]. Pump assembly located in bottom left, removed associated hoses, Marked wired colors on pump housings and removed. Removed assembly. Unscrewed pump, installed new pump and reversed procedure to reassemble. Struggled mostly with replacing spring around front seal. Stretch it as far apart as you can as you "roll" the spring in and then massage the seal to get the spring into correct position. Definitely a doable repair. Good Luck.
Was this instruction helpful to you?
Thank you for voting!
Customer:
william from Mobile, AL
Parts Used:
AHL72914402
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
The bolt on the motor rotor loosened allowing the motor shaft to wallow out the plastic bushing in the rotor.
Unplugged the washer,removed the rear cover, removed the old rotor assembly & installed the new rotor with thread lock on the retaining bolt.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bruce from West Hills, CA
Parts Used:
4738ER1002A
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
My Washer was leaking
The repair went well and your parts are easy to find. This is the second time I have used your services and both times have been great. Your parts are at great prices and your delivery is a lot faster that one would think.
Thank you
Was this instruction helpful to you?
Thank you for voting!
Customer:
gerald from wis dells, WI
Parts Used:
5220FR2006H
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
the water inlet was leaking
pulled off top of washer to get at the inlet valve disconnect two hoses take two screws out and then you put it back together the way you took apart and your done
Was this instruction helpful to you?
Thank you for voting!
Customer:
Drew from Thomaston, GA
Parts Used:
5221ER1003A
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
I had a slow leak coming from the factory cold inlet water valve assembly, and removed the top and found it rusted.
I removed the top off the washer, unplugged from the electrical, removed the three hoses and wiring plugs, removed the two screws holding the valve assembly in place, and replaced the part with the new. It was a very simple swap, and I even found a video on YouTube on how to replace it.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Asheville, NC
Parts Used:
5220FR2006H
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Water inlet valve coil was leaking water.
Unplug Washing machine first. Then remove 2 screws at the back of the top cover. Slide the top cover back then lift and remove. Unplug electrical connector @ inlet valve and remove water lines 1 going in and 1 out of valve. Remove 2 screws holding assembly in place then install new valve assembly and all other components in reverse order.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WM2250CW
121 - 135 of 211