Models > WT1301CW > Instructions

WT1301CW (ABWEPUS) LG Washer - Instructions

Jump to:

All Instructions for the WT1301CW

Customer:: Marilyn from THOMASTON, GA
Parts Used:: AGZ72909711
Difficulty Level:: Very Difficult
Total Repair Time:: 30 - 60 mins
Tools:: Nutdriver

could not get the 10 mm nut to loosen

Tried everything and could not get it out I just use mesh bags for washing at this time, but LG washing machine is the worst I have ever had

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Kristen from Safford, AZ
Parts Used:: AGZ72909711, 5006EA3009B
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers, Socket set

Washer pulsator was coming loose during wash cycle.

Since the old pulsator had actually come off during a wash cycle, I was able to place the new one on easily. Tightened the screw with a socket. Then placed the new cap on. Before placing the new pulsator on, I was able to clean all the mold and hard deposits off the mechanism under the pulsator. The hard deposits were also scrapped from the pulsator holding (where the screw goes) which may have caused the problem to begin with.

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: John from TUCSON, AZ
Parts Used:: MEF62462103
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins

Lid hinge pin receptor (MEF62462103) broken

Remove cover over associated hinge pin assembly and the hinge assembly behind it. With the lid open, remove 4 screws holding on the top assembly, lift and rotate it on its wire cable side and rest it on the machine top frame (it may be necessary to remove the 2 cable restrainers to gain enough play to do this - you will have to remove the large rear cover to accomplish this and be able to reinstall these restrainers). Remove 2 screws fastening the broken hinge pin receptor, install new unit, and fasten with these 2 screws. Install top assembly and a new/repaired hinge pin assembly (most likely the reason for the broken hinge pin receptor).. Replace cable restrainers and rear cover if it was necessary to remove them. Note: These hinge pin assemblies are sold as a set (1 left, 1 right; they are not interchangeable and are expensive). Time to do repair = about 30 minutes.

3 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Jim from Crystal Lake, IL
Parts Used:: AJU75152601
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins

During the spin cycle water continued to flow into the machine.

unplugged machine, turned off water valves. Moved machine away from the wall. Disconnected supply lines. Removed cover housing water valve assembly.
Took a picture with phone. Disconnected water and electrical wires. Removed water valve assembly . Installed new assembly ,cover and reconnected supply lines, plugged power cord in, turned on water supply valves. Done.

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: cathy. from etna, OH
Parts Used:: AEM73732901
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

WATER WAS NOT SHUTTING OFF

I HAD A CHAT WITH LG EXPLAINED THE PROBLEM . SAID IT WAS THE WATER SHUT OFF VALUE. V EVEN SENT THE PAGE WITH PART# TO ORDER ONLINE.

LOVE LG CHAT!!!

3 of 13 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Roger from Bradenton, FL
Parts Used:: AAZ72925601
Difficulty Level:: Very Easy
Total Repair Time:: Less than 15 mins

Detergent and Softner dispenser was not working peoperly

The old dispenser is removed by slightly raising the front as you pull it out of the housing slot. To install the new dispenser, keep the front slightly tilted up and insert the new dispenser into the housing alot

3 of 14 people found this instruction helpful.

Was this instruction helpful to you?

All Instructions for the WT1301CW