WT1501CW (ABWETUS) LG Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from PARKER, CO
- Parts Used:
- MCK67634401
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
One side of the lid or top door of the washer cracked. Would not lock and stay close during wash cycle.
Removed flimsy, easily breakable panels (one on each side), that cover the hinges for the top lid. Removed screws that cover the pins in the door top, that fit in the swivel. Removed broken door.
Placed pins in new door into swivel brackets, replaced covers that hold the door correctly in place. Tightened in place with screws. Pot panels back into pace to cover the swivel mechanism.
Job complete.
Sorry for the written confusion, don’ see a way to attach photos that make it simple to understand.
Placed pins in new door into swivel brackets, replaced covers that hold the door correctly in place. Tightened in place with screws. Pot panels back into pace to cover the swivel mechanism.
Job complete.
Sorry for the written confusion, don’ see a way to attach photos that make it simple to understand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Heinz from SARASOTA, FL
- Parts Used:
- MEF62462103
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
RIGHT HINGE BROKE
Removed 2 hidden screws from the top panel.
Lifted top panel.
The first screw came out easy, the second one gave me trouble.
It is best to help a helper who can hold the lid open as much as possible.
To insert the new screws takes patience as they might fall very easily.
Overall, not that difficult - just need patience.
Lifted top panel.
The first screw came out easy, the second one gave me trouble.
It is best to help a helper who can hold the lid open as much as possible.
To insert the new screws takes patience as they might fall very easily.
Overall, not that difficult - just need patience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from SIMI VALLEY, CA
- Parts Used:
- AEM73732901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Drain hose had a pin hole leak external to washer
Very close to the installation video online at Parts Select. Removed the back panel, unclipped the hose from the inner fitting and replaced with the rear hose. Why it didn;t leak on the inside is interesting as there was no clip on the at the inner fitting.
The one difference from the existing install video online was that I didn't have to tip the washer over ~75 degs before replacing. I instead found that I could put to cinder blocks under the back edge to replace the drain hose. This made the job quicker without having to worry about having a box for it to rest on (with any risk of falling to the floor).
The one difference from the existing install video online was that I didn't have to tip the washer over ~75 degs before replacing. I instead found that I could put to cinder blocks under the back edge to replace the drain hose. This made the job quicker without having to worry about having a box for it to rest on (with any risk of falling to the floor).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas m from CARMICHAEL, CA
- Parts Used:
- 4263FA3933C
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
leg broke off inside housing
raised the front of washer by hand (literally) and placed two 2x4 blocks under front lip for support. reached up inside washer cabinet and unscrewed the broken leg piece upwards into the cabinet. this was the only way I could get the broken piece out without some specialized tool to reach it from the underside. replacement with the new leg was a breeze.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from SHELBY TWP, MI
- Parts Used:
- MEF62462103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Plastic hinge broken on RHS.
Description provided on website was that repair was similar to another washing machine where you press in on spring clips to release top of machine to access hinge. Not correct at all.
There are two screws on top of machine that are covered by caps. Remove caps and then remove screws. Lift up / prop up machine top and you have easier access to 2 screws that hold plastic hinge in place. Remove screws and replace hinge and replace screws. Took me longer to figure out I had incorrect directions than it did to replace hinge.
There are two screws on top of machine that are covered by caps. Remove caps and then remove screws. Lift up / prop up machine top and you have easier access to 2 screws that hold plastic hinge in place. Remove screws and replace hinge and replace screws. Took me longer to figure out I had incorrect directions than it did to replace hinge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Thomasville, GA
- Parts Used:
- MEF62462103
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The right plastic hinge broke
The instructions received from partselect.com were really good. There are two long screws located on either side of the front control panel. Simply removed the small covers to expose the two screws. Then remove both screws. At that point you can lift up (carefully) the front panel high enough to gain access underneath to remove the two Philip head screws holding the hinge. Be careful not to drop the screws down in the machine cavity. Lift out the old hinge and insert the new one. Re-install the two Phillip head screws into the new hinge. Let the front panel back down and re-install the two long screws. You’re done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Lovettsville, VA
- Parts Used:
- MEF62462103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic hinge broke when closing the washer lid. This piece connects with the slow closing mechanism for the lid.
Removed both slow closing latches (3 Phillips head screws each) and lifted off the lid.
Pried off the two plastic caps on the top front of the machine. They are about 1/2" or so in diameter and I used a very thin flat head screwdriver to remove.
Unscrewed the Phillips head screw under each plastic cap.
Popped the two plastic covers (with the warning labels) off the hinges/closing mechanisms with thin flat head screwdriver.
Pulled dryer out from wall, unplugged the unit from the A/Power, and removed the phillips head screw on each side of the washer back.
Lifted off the washer top with the aid of assistant to hold close to the machine. Be careful with the cable that leads to the control panel.
On the underside of the top, I removed the two Phillips head screws holding the broken hinge and pushed it out from the top.
Replaced the hinge and re-inserted and tightened the two Phillips screws holding it in. Took the opportunity to thoroughly clean the top of the washer tub.
Re-installed the two back and two front screws that hold down the top and popped the two plastic covers on the top.
Moved the lid back into place and slid the slow closing latches back into place and reinstalled the 3 screws in each one. Note how the latch goes back into the hinge. Snapped the two covers back into place.
Plugged in the machine and pushed it back into place.
Lid soft closes perfectly now.
Pried off the two plastic caps on the top front of the machine. They are about 1/2" or so in diameter and I used a very thin flat head screwdriver to remove.
Unscrewed the Phillips head screw under each plastic cap.
Popped the two plastic covers (with the warning labels) off the hinges/closing mechanisms with thin flat head screwdriver.
Pulled dryer out from wall, unplugged the unit from the A/Power, and removed the phillips head screw on each side of the washer back.
Lifted off the washer top with the aid of assistant to hold close to the machine. Be careful with the cable that leads to the control panel.
On the underside of the top, I removed the two Phillips head screws holding the broken hinge and pushed it out from the top.
Replaced the hinge and re-inserted and tightened the two Phillips screws holding it in. Took the opportunity to thoroughly clean the top of the washer tub.
Re-installed the two back and two front screws that hold down the top and popped the two plastic covers on the top.
Moved the lid back into place and slid the slow closing latches back into place and reinstalled the 3 screws in each one. Note how the latch goes back into the hinge. Snapped the two covers back into place.
Plugged in the machine and pushed it back into place.
Lid soft closes perfectly now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willie from Loganville, GA
- Parts Used:
- AJU75152601
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer water would not stop running
Turn water valves off , remove the hoses from washer,remove covering from hose housing, remove the claps from back off housing, remove screws from intake housing, remove iPod intake and install new housing and reverse the install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from EDWARDS, IL
- Parts Used:
- AGZ72909711
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Wrench set
very dirty under adjitator cap and pulsator
Tried to remove adjitator but it was stuck. Could not find any professional method of pulling it. There must be some type of puller,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Lakeside, CA
- Parts Used:
- AJU75152601
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Cold water valve leaking.
turn off the water, unplug washer from power. remove two screws holding rear top plate. Here's the hard part. Pry the rear top plate from the top of the washer. It has multiple snap in guides across the front edge and they are very tight. Be careful and apply steady pressure straight up and they will eventually come free.
I marked each of the electrical inputs going to the old valve before removing. Remove the wiring harness. Again be careful and ease them off. the connectors
come apart easily. Remove the hose clamps with pliers and slip off the hoses. They are long enough that I trimmed off the soft ends of the old hoses and still had plenty of hose to reconnect. Remove the filler hoses. Remove the screws holding the valve to the machine. Re install the new valve in reverse order. Goes back in very easily.
Make sure to secure all the hoses. Run a wash cycle with an empty tub to make sure everything is working properly and nothing is leaking. Snap the rear top plate back into position and secure with the two screws Should take less than a couple of hours to do this job. Again the hardest part is getting the rear top plate off.
I marked each of the electrical inputs going to the old valve before removing. Remove the wiring harness. Again be careful and ease them off. the connectors
come apart easily. Remove the hose clamps with pliers and slip off the hoses. They are long enough that I trimmed off the soft ends of the old hoses and still had plenty of hose to reconnect. Remove the filler hoses. Remove the screws holding the valve to the machine. Re install the new valve in reverse order. Goes back in very easily.
Make sure to secure all the hoses. Run a wash cycle with an empty tub to make sure everything is working properly and nothing is leaking. Snap the rear top plate back into position and secure with the two screws Should take less than a couple of hours to do this job. Again the hardest part is getting the rear top plate off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from TUCSON, AZ
- Parts Used:
- MEF62462103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lid hinge pin receptor (MEF62462103) broken
Remove cover over associated hinge pin assembly and the hinge assembly behind it. With the lid open, remove 4 screws holding on the top assembly, lift and rotate it on its wire cable side and rest it on the machine top frame (it may be necessary to remove the 2 cable restrainers to gain enough play to do this - you will have to remove the large rear cover to accomplish this and be able to reinstall these restrainers). Remove 2 screws fastening the broken hinge pin receptor, install new unit, and fasten with these 2 screws. Install top assembly and a new/repaired hinge pin assembly (most likely the reason for the broken hinge pin receptor).. Replace cable restrainers and rear cover if it was necessary to remove them. Note: These hinge pin assemblies are sold as a set (1 left, 1 right; they are not interchangeable and are expensive). Time to do repair = about 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristen from Safford, AZ
- Parts Used:
- AGZ72909711, 5006EA3009B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Washer pulsator was coming loose during wash cycle.
Since the old pulsator had actually come off during a wash cycle, I was able to place the new one on easily. Tightened the screw with a socket. Then placed the new cap on. Before placing the new pulsator on, I was able to clean all the mold and hard deposits off the mechanism under the pulsator. The hard deposits were also scrapped from the pulsator holding (where the screw goes) which may have caused the problem to begin with.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from THOMASTON, GA
- Parts Used:
- AGZ72909711
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
could not get the 10 mm nut to loosen
Tried everything and could not get it out I just use mesh bags for washing at this time, but LG washing machine is the worst I have ever had
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Crystal Lake, IL
- Parts Used:
- AJU75152601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
During the spin cycle water continued to flow into the machine.
unplugged machine, turned off water valves. Moved machine away from the wall. Disconnected supply lines. Removed cover housing water valve assembly.
Took a picture with phone. Disconnected water and electrical wires. Removed water valve assembly . Installed new assembly ,cover and reconnected supply lines, plugged power cord in, turned on water supply valves. Done.
Took a picture with phone. Disconnected water and electrical wires. Removed water valve assembly . Installed new assembly ,cover and reconnected supply lines, plugged power cord in, turned on water supply valves. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cathy. from etna, OH
- Parts Used:
- AEM73732901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
WATER WAS NOT SHUTTING OFF
I HAD A CHAT WITH LG EXPLAINED THE PROBLEM . SAID IT WAS THE WATER SHUT OFF VALUE. V EVEN SENT THE PAGE WITH PART# TO ORDER ONLINE.
LOVE LG CHAT!!!
LOVE LG CHAT!!!
Was this instruction helpful to you?
Thank you for voting!