T1327AGPP LG Washer - Instructions

I noticed that my washer was leaking water into the tub. It was dripping, very slowly, but it was dripping. I noticed first, because it was starting to smell, and I didn’t understand why. Once I noticed that it was dripping, I checked online and noticed that the solenoid water inlet is most likely the problem. I found the part on parts, select, and confirmed with my model. The pictures were very close and similar, so I was pretty sure I was getting the cracked part. Once I received the part, it was time to fix it. You just have to turn the water supply off, remove the inlet lines with a adjustable wrench, if necessary, and then get to the washer. Make sure you also unplug the washer. There are only two Phillips head screws to remove to get the vanity cover off of the back. For whatever reason my removal was a little bit difficult for this. There are some plastic clips that hold the front portion on of the vanity plate. These were very tight, and I was afraid I would break them, but eventually they came loose with gentle upward pulling. Once this was off, it was super easy to identify the part that needed replacement. There are two hose clamps that you just need a pair of pliers to squeeze in slide off the hose. Then you remove three additional Phillips head screws, and the other connections pop out on their own. The solenoid plugs are very simple to slide off, and it is really difficult to put them on any other way. If you need to, you can take a few photos of the installation. Once you have the old one out, hook up the hoses first, and slide the hose clamps back to their original position. Once you have the two black hoses back on, reposition the new valve body, and slide the additional three prongs into the inlet soap dispenser. Make sure that the fit is snug. Don’t over push, the parts are plastic. Once this is done, reinsert, the three Phillips screws into their holes. Then you can reconnect the solenoids. At this point the replacement is done, and all you have to do is replace the vanity cover. Take time to ensure that you’ve done this correctly. I left the vanity cover off and ran a test load of dirty clothes to make sure that there were no leaks. Once I assure, there were no leaks, I put the vanity cover back on and put the two screws on. This was a very easy fix. Again, just go slow removing the vanity plate so you do not crack or break the tines in the front.

After unplugging the washer I cut the water off. I took the water hoses off, then the back top panel using a phillips head screw driver. I then used a pair of pliers to take off the two hoses and clamps. I unplugged the electric connection on each solenoid, took out 5 screws replaced the part and did everything in reverse order. Problem solved. Thanks for the fast service on my order.

The teeth in the pulsator assembly where stripped out on the original plate.

Ordered the replacement and it was 1 screw to undo and pop in the new assembly. Super easy repair

Tried to remove adjitator but it was stuck. Could not find any professional method of pulling it. There must be some type of puller,

unplugged machine, turned off water valves. Moved machine away from the wall. Disconnected supply lines. Removed cover housing water valve assembly.
Took a picture with phone. Disconnected water and electrical wires. Removed water valve assembly . Installed new assembly ,cover and reconnected supply lines, plugged power cord in, turned on water supply valves. Done.

Very close to the installation video online at Parts Select. Removed the back panel, unclipped the hose from the inner fitting and replaced with the rear hose. Why it didn;t leak on the inside is interesting as there was no clip on the at the inner fitting.
The one difference from the existing install video online was that I didn't have to tip the washer over ~75 degs before replacing. I instead found that I could put to cinder blocks under the back edge to replace the drain hose. This made the job quicker without having to worry about having a box for it to rest on (with any risk of falling to the floor).

Tried everything and could not get it out I just use mesh bags for washing at this time, but LG washing machine is the worst I have ever had

Since the old pulsator had actually come off during a wash cycle, I was able to place the new one on easily. Tightened the screw with a socket. Then placed the new cap on. Before placing the new pulsator on, I was able to clean all the mold and hard deposits off the mechanism under the pulsator. The hard deposits were also scrapped from the pulsator holding (where the screw goes) which may have caused the problem to begin with.

I HAD A CHAT WITH LG EXPLAINED THE PROBLEM . SAID IT WAS THE WATER SHUT OFF VALUE. V EVEN SENT THE PAGE WITH PART# TO ORDER ONLINE.

LOVE LG CHAT!!!

The problem ended up being the pump motor which discharges water from the washer. I figured out this was the problem after trying several things. I determined the motor was fine when it was empty. With the unit turned off, if you can rotate the tube with a quick spin and it lights up, probably this is OK. Then I tried to run it again and it went about 1/2 way through the cycle and stopped and started humming again. So I started emptying out the water, which I noticed was about 5 gallons which is way too much. so once empty, I took the pump off by turning unit on side. There are two hoses with hose clamps, and a few screws. Be careful to mark which wire plugs onto which side of the pump. One is brown and one is black. If you take the pump housing off, with the 3 screws, you should be able to pull the motor apart. Mine had water and scum from the wash in it, which was a dead give away that it was the problem.