KHWV01RSS0 KitchenAid Washer - Instructions

Disconected washer, disconected water lines, Removed top cover. Removed screw holding valve, disconnected 2 connectors for valve put everything back together

Plastic door hook was broken in half and door lock (DL) error code was showing-- though the hook was still in the door (each half held in by its own screw) and the door actually felt as if it was still latching o.k. After reading some things online, I though it was worth buying new hook since it was cheap, and giving it a try. Got it for a total of about $11.00 a little over 48 hours after placing order. It took about a minute to put it in. Then, tried to start the washer and "Voila"-- same error code still appeared! Read some more stuff online and saw a recommendation for "restting" this error by unplugging and replugging the pink wire harnesses at the back left of the top of the machine, after taking off the top (held on by just 3 screws at the back edge). So I did this (after first unplugging power cord), and this time "Voila", it worked! So I assume the error code was initially caused by the broken plastic hook, but the code stayed in the system (even though I had also tried unplugging the power earlier)- and then was cleared off when I did wired harness unplug/replug operation. So the situation was a little puzzling, but still an "easy fix" overall.

Took the outer ring off with the help of pliers just be careful. Push the bellow into the washer. We cleaned the area good at this time. Put the new bellow in being sure to keep the wrinkles out and securing it in place with the other clamp. Make sure to keep it lined up and wrinkle free to prevent leaks and possible tears later on. You will need the screwdriver to tighten the screws in the inner clamp.

I just take out the botton part and fine what part what i need chage and just chage exactly like the old if yoo dot remember all the wires please take pictures and you hava guia to check went you are finished

i tore down the "tech use only" pamphlet from inside of the machine.i am an auto tech by the way. so i got into the onboard computer of my machine using this pamphlet.the machine's computer took over and went through a series of tests, which pointed me to the correct location of the problem.i acted on that info and replaced my water inlet valve. the actual code was " FH ".

Followed video, slowly. Was easier then I expected. Everything fit perfectly.

pulled the front and top of the machine off, pulled off the old bellow, ordered the new bellow, and put the new bellow on. we looked on youtube.com for a video on repairing the machine.

My son pulled the washer out and found the parts that was leaking. He ordered the parts from your company. they arrived the next day and he re-pared the leaks and all is well.thank you

Slid the washer out, took the hoses off and the back panel then the front panel, found coins in the filter tray and a baby bottle plastic cap was sealinhg the drain going into the plastic filter housing (it fits perfectly) removed all the items and put the white plastic screw cap back on the drain. Next problem was the washer walking around the laundry room, upon fixing the drain problem noticed the front shock absorber was unhooked and two on the right side of the machine had leak some grease, rehook the front shock and ordered two new ones it don't walk around anymore and works smooth and quiet now. I also have to add that Parts Select has been absolutely GREAT had the parts, delivered when promised.

It was easy as soon as I previewed a video on how to repair bellow it was all about unscrewing some screws and removing some parts but was simple steps that anyone can do themselves only thing that gave me very little trouble was putting the spring coil around the bellow needed my husband to help me a little so it wouldn't come out place while stretching the spring to make sure everything was good and secure and ran a test washer to make sure it didn't leak afterward.the baffle was very easy to replace with very little pressure I was able to slide it till I heard a click sound and it was secure did laundry same day and every was wonders very happy I was able to save some money on labor :)

Very limited access to the bellow clamp. Found it easier to first remove washer front panels (8 screws total), providing ready access to R&R the bellow. 40 minutes tops.

Followed video clip that I found online

I removed the top 3 screws on the rear, removed soap dispenser, removed screw in front corner at soap dispenser,pry off control panel with flat head screwdriver lay on top, removed spring around bellows at door opening, remove 4screws holding door assembly, disconnect 3 molded plugs serving door lock, you will need to hold door while you loosen bellows clamp.Reverse process note: soap dispenser tube can be removed to clean without any tools. It is some much easier when you remove the front door assembly.T-20 torx screwdriver, 9/32 socket Theirs a you tube video also.ghw

Removed the 3 bolts attaching top of washer. Disconnected hoses from the inlet value and flow meter, also very careful to remove the wire connections. Removed Water inlet valve (this requires the star screw driver). Did find it best to connect the inlet valve and flow meter before reattaching the inlet valve, as that sits under the lip, it is just a bit of a tight fit to get the hose reconnected between the two. Then reconnected the flow meter hose to the dispensing box, reattached the hoses and ran a cycle no f20 issues, as a note, an f20 has to do with a restriction in the flow of water not with pressure so not sure if it was the inlet valve or flow meter clogging up or both.

A real novice at dyi. Found what the error code meant in the manual and google searched it online. Found Youtube video on repair and was successful in getting the washer to work a few times before the error code returned. Decided to replace the inlet valve and on your site took the advice of a previous user and also changed the flowmeter. Could not have been a better experience. Easy to find the correct parts for my model and got great tips...plus your shipping was excellent. Thanks!